Sinclair ASCU-12A Скачать руководство пользователя страница 86

Страница: 86 / 202

U-MATCH AIR CONDITIONERS INSTALLATION

The air-conditioning unit shall have special power supply line which shall be equipped with

electricity leakage switch and air switch, so as to deal with overload conditions.

The air-conditioning unit must have grounding to avoid hazard owing to insulation failure.

All fitting lines must use crimp terminals or single wire. If multiple twisted wires are

connected to terminal board, arc may arise.

All line connections must conform to the schematic diagram of lines. Wrong connection may

cause abnormal operation or damage of the air-conditioning unit.

Do not let any cable contact the refrigerant pipe, the compressor and moving parts such as

fan.

Do not change the internal line connections inside the air-conditioning unit. The

manufacturer shall not be liable for any loss or abnormal operation arising from wrong line

connections.

4.1.3 Power Cable Connection

1) Air-conditioning unit with single-phase power supply

①

Remove the front-side panel of the outdoor unit.

②

Pass the cable though rubber ring.

③

Connect the power supply cable to the “L, N” terminals and the grounding screw.

④

Use cable fastener to bundle and fix the cable.

2) Air-conditioning unit with 3-phase power supply

①

Remove the front-side panel of the outdoor unit.

②

Attach rubber ring to the cable-cross hole of the outdoor unit.

③

Pass the cable though rubber ring.

④

Connect the power cable to the terminal and earthing screws marked “L1, L2, L3 & N”.

⑤

Use cable fastener to bundle and fix the cable.

Caution:

For air-conditioner with auxiliary heater, it is required to connect the power cable to the “L1,

L2 L3”terminals and the grounding screw.

4.1.4 Connection of Signal Line of Wire Controller

Caution:

Take great care when carrying out the following connections, so as to avoid malfunction of
the air-conditioning unit because of electromagnetic interference.

The signal line of the wire controller must be separated from the power line and the

connecting line between the indoor unit and the outdoor unit.

◆

In case the unit is installed in a place vulnerable by electromagnetic interference, it is

better to use shielded cable or double-twisted cable as the signal line of the wire controller.

Open the cover of the electric box of the indoor unit.

Pull the signal cable of the wire controller through the rubber ring.

Содержание ASCU-12A











































































































































































































Результаты поиска

Содержание ASCU-12A

Отзывы:

Бренды по названию

Популярные бренды

Sinclair ASCU-12A, Руководство по обслуживанию

Результаты поиска

Содержание ASCU-12A

Отзывы:

Бренды по названию

Популярные бренды