Simrad GO XSE Series Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 242

background image

Using the cursor on the panel

When you position the cursor on the panel, the image pauses and
the cursor information window is activated. The left/right distance
from the vessel to the cursor are shown at the cursor position.

Viewing history

In a SideScan view, pan the image to see sides and history by
maneuvering the image left, right, and up.
To resume normal SideScan scrolling, select the clear cursor option.

Recording SideScan data

Displays the record log dialog. SideScan data can be recorded by
selecting the correct file format (xtf) in the record dialog. For more
information, refer to

"Recording log data"

Setting up the image

Use the SideScan menu to set up the image. When the cursor is
active, some options in the menu are replaced with cursor mode
features. Select the clear cursor option to return to the normal
menu.

Source

Ú

Note:

Available only if multiple sources with the same

capability are available.

Used to specify the source for the image in the active panel.
You can display different sources simultaneously, using a multi-
panel page configuration. Menu options for each panel are
independent.

Ú

Note:

Using transducers at the same frequency can cause

interference.

160

SideScan

| GO XSE/XSR Operator Manual

«
...
158
159
160
161
162
...
»

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Бренд: Omnia Страницы: 8

Бренд: Modulate Страницы: 2

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Uniden Страницы: 32

Бренд: Uniden Страницы: 40

SUNDOWNER UH-011

Бренд: Uniden Страницы: 10

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренд: Park House Healthcare Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды