5
SimpliFire • SF-BI30-E, SF-BI36-E Service Manual • 2040-910 • 8/13
Lighting LED Replacement (continued)
17. Remove all three lighting LED circuit boards.
18. Install replacement lighting LED circuit boards into
the appliance. Fully engage each barbed clip. See
Figure 5.
19. Connect all three lighting LED power source
connectors to the three LED circuit boards. See
Figure 6.
20. Install metal brackets by attaching with four screws.
See Figure 4.
21. Install the brick panel into the rear of the cavity.
Ensure that it is located so that the notch is in the
lower right of the cavity. See Figure 12.
22. Install replacement refractory panels. Align tabs
on back edge of the panel with the slots in the rear
appliance cavity. Once the tabs are engaged,
carefully install the front edge of the appliance cavity.
Take care to apply even pressure to prevent damage
to the replacement panels. See Figure 10 & 11.
23. Reconnect the fi ve connectors from the Blower/
Heater module to the appliance. See Figure 9.
24. Carefully align the Blower/Heater module horizontally
with the opening of the appliance. Install it straight
into the opening so that the back edge interlocks
with the back wall of the appliance.
25. While supporting the Blower/Heater Module, install
the four screws across the upper face of the
appliance. See Figure 8.
26. Install the four thumb screws and metal angle
bracket in the upper rear of the appliance cavity.
See Figure 7.
27. Rotate log ember bed and align with fl oor of opening.
Engage back side of ember bed into the opening.
Pivot the front of the ember bed into position fl at on
the fl oor of the opening. Take care not to pinch
wiring under log ember bed.
28. Align the grate, with the retained screws, with the
steel brackets under the ember bed. Ensure that
wiring is not pinched between log ember bed and
steel bracket.
29. Install and tighten the screw in each end of the
grate. See Figure 2.
30. Install rubber plugs into holes in each end of grate.
See Figure 2.
31. Install glass into bottom retainer channel.
32. Install C-channel on top edge of glass panel.
33. Align C-channel with screw holes in appliance.
See Figure 1.
34. While supporting glass, install both screws through
top C-channel retainer into appliance.
Blower/Heating Module Replacement
1. If necessary, place a drop cloth or other material on
the hearth or fl ooring to prevent scratching. Grasp
front with two hands. Pull straight back to disengage
front from appliance.
2. Locate C-channel that retains top edge of glass
panel. While supporting the glass, remove the screw
located in the C-channel at the top two corners of the
glass panel. See Figure 1.
3. Pivot glass away from appliance and lift out of bottom
retainer channel.
4. Remove four thumb screws and metal angle bracket
from upper rear of appliance cavity. See Figure 7.
5. Remove four screws from upper face of appliance.
Take care to support the Blower/Heater Module while
the screws are removed. See Figure 8.
6. Remove the Blower/Heater Module by lifting back
edge slightly then pulling it straight back from the
appliance opening. This will reduce the likelihood of
damaging the brick panels.
7. Locate the fi ve electrical connectors on the right
side of the appliance cavity. Disconnect each of the
fi ve connectors. See Figure 9.
8. Reconnect the fi ve connectors from the replacement
Blower/Heater module to the appliance. See Figure
9.
9. Carefully align the Blower/Heater module horizontally
with the opening of the appliance. Install it straight
into the opening so that the back edge interlocks with
the back wall of the appliance.
10. While supporting the Blower/Heater Module, install
the four screws across the upper face of the
appliance. See Figure 8.
11. Install the four thumb screws and angle metal
bracket in the upper rear of the appliance cavity.
See Figure 7.
12. Install glass into bottom retainer channel.
13. Install C-channel on top edge of glass panel.
14. Align C-channel with screw holes in appliance.
15. While supporting glass, install both screws through
top C-channel retainer into appliance. See Figure
1.
16. Install front by aligning the tabs on its back side with
the spring clips on the face of the appliance. Press
evenly with two hands to fully engage the front to the
appliance.
35. Install front by aligning the tabs on its back side with
the spring clips on the face of the appliance. Press
evenly with two hands to fully engage the front to the
appliance.
