manualshive.com logo in svg

Simplicity SYNERGY X9.4, Руководство по обслуживанию

Поделиться
Скачать
Simplicity SYNERGY X9.4 Скачать руководство пользователя страница 27

071807 

III. General Troubleshooting

 24    

                                  

D. Excessive Vibration

1. Check the direct air fan for damage.  Replace if necessary. (See 

II. Maintenance Procedures, J. Replacing the Direct Air Motor Fan

)

2. The agitator/brushroll may be out of balance.
3. To test the agitator/brushroll for balance:
Models .4 and older:

1. Remove the agitator/brushroll and run the direct air motor.

2. If vibration stops with the agitator/brushroll removed, replace the agitator/brushroll and retest.

Models .5 and newer:

1. Remove the nozzle cover and install the hall sensor test plug.  (If test plug is not installed, the direct air motor will only run 2 to 

3 seconds and then shut off.)

2. Remove the agitator/brushroll and run the direct air motor.

3. If vibration stops with the agitator/brushroll removed, replace the agitator/brushroll and retest.

E. Agitator/brushroll Does Not Rotate

1. Check the condition of the belt.  Replace if necessary.
2. Check the agitator/brushroll for excessive hair build-up.  Clean agitator/brushroll if necessary.
Also see 

III. General Troubleshooting, B. Direct Air Motor Will Not Run

Содержание SYNERGY X9.4







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды