background image

3

Safety

Slope Operation

Operation on slopes can be dangerous. Using the unit on a slope
that is too steep where you do not have adequate wheel traction
(and control) can cause sliding, loss of steering, control, and
possible rollover. You should not operate on a slope greater than a
5.4 foot rise over a 20 foot length (15 degrees).

Always mow across slopes, not up and down (to maintain traction
on the wheels) and avoid sudden turns or rapid speed changes.
Reduce speed and use extreme caution on ALL slopes.

Also, note that the surface condition you are on can greatly impact
your ability to safely operate this machine. Operating on wet or
slippery slopes can cause sliding and loss of steering and control.
Do not operate on slopes that are slippery, wet, or have soft soil
conditions.

If you feel unsure about operating the unit on a slope, don’t do it.
It’s not worth the risk.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and
throw debris that could seriously injure a bystander. Be sure to clean
up the area to be mowed and remove objects that could be thrown by
the blade BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge
guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running!  If
someone does enter the area, shut the unit off immediately until they
leave.

Moving Parts

This equipment has many moving parts that can injure
you or someone else. However, if you stay in the operator
zone (stay seated in the seat), and follow the safety rules
in this operator’s manual, the unit is safe to operate.

The mower deck has spinning mower blades that can
amputate hands and feet. Do not allow anyone near the
unit while it is running!  Keep safety devices (guards,
shields, and switches) in place and working.

To help you, the operator, use this equipment safely, it is
equipped with an operator-present safety system. Do NOT
attempt to alter or bypass the system. See your dealer
immediately if the system does not pass all the safety
interlock system tests found in this manual.

Safety Rules and Information

Not 

for  

Reproduction

Содержание 5100723













































Отзывы: