Simplicity 5022285 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 38

Simplicity 5022285 Скачать руководство пользователя страница 33

Troubleshooting, Adjustment & Service

Figure 29. Neutral Spring Return Adjustment
A. Clevis
B. Jam Nut
C. Neutral Return Rod

RETURN-TO-NEUTRAL
ADJUSTMENT

To determine if it is necessary to adjust the neutral
return, perform the following steps.

1. Disengage the PTO, engage the parking brake and

turn off the engine.

2. Move the ground speed control levers into the

operating position, pull levers rearward and release.

3. Move the ground speed control levers out towards

the neutral position. If the levers do not align with
the notches in the neutral lock plate, it is necessary
to adjust the neutral return rod (C, Figure 29).

Adjustment

1. Loosen the jam nut (B) locked against the clevis (A).

2. Turn the neutral return rod (C) to adjust handle

position.

4. Pull lever rearward and release to check position

again. Adjust as necessary to align levers with
notches.

It is important to note that after every adjustment of the
neutral return rod, the lever must be pulled rearward and
released to properly check the neutral position.

5. Once the lever alignment has been adjusted, lock

jam nut against the clevis.

NEUTRAL ADJUSTMENT

If the tractor “creeps” while the ground speed control
levers are locked in NEUTRAL, then it may be
necessary to adjust the linkage rod.

NOTE: Perform this adjustment on a hard, level surface
such as a concrete floor.

1. Disengage the PTO, engage the parking brake and

turn off the engine.

2. There are three nuts (B, Figure 30) on the linkage

rod. The first two are to be used together to turn the
rod and the third (towards the front of the machine)
is used to lock the rod in place. Loosen the jam nut
that locks against the ball joint (B, Figure 30) and
turn the linkage rod (A) to adjust. If the machine
creeps forward, turn the rod CLOCKWISE (while
standing at the rear of the machine, facing forward),
if the machine creeps backward, turn the rod
COUNTER-CLOCKWISE.

3. Lock the jam nut (B) against the ball joint when

neutral is achieved.

NOTE: This adjustment should not be performed while
the machine is running. It may take several attempts to
achieved neutral, depending upon how much the
machine creeps.

Figure 30. Neutral Adjustment
(RH side shown)
A. Adjustment Linkage Rod
B. Nuts

A

B

A

B

C

29

«
...
31
32
33
34
35
...
»

Содержание 5022285







































Отзывы:

Нет отзывов