Simplex Silver Lite P71, Руководство по эксплуатации

Страница: 2 / 4

NOTE: BE SURE TO READ THESE INSTRUCTIONS COMPLETELY BEFORE OPERATING
ANY PUMP. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL
INJURY AND/OR DAMAGE TO THE PUMP.
KEEP AWAY FROM FIRE AND HEAT
Keep your equipment away from excessive heat
which tends to soften the packings. For best
performance, DO NOT expose equipment to
temperatures above 160 F.
ASSEMBLY
1. Remove SHIPPING PLUG from the 3/8"
NPT port and discard (refer FIGURE 1).
NOTE: THE PLUG IS STRAIGHT THREAD
TO PREVENT DISTORTION TO THE 3/8”
NPT THREADING.
2. Assemble hose or quick-disconnect coupling
directly to this port. Use a sealant or Teflon
to seal threads.
3. The reservoir is vented so there is no need
to open any air vents prior to using the
pump.
WORKING PRESSURE
The pump's maximum working pressure is
10,000 PSI (700 kg/cm 2). Make sure that all
hydraulic equipment such as rams, hoses, etc.
used with this pump is rated at 10,000 PSI
operating pressure.
HYDRAULIC CONNECTIONS
Never disconnect or connect any hydraulic
hoses or fittings without first unloading the
ram. Open the release valve counter-
clockwise to assure that the system has
been depressurized. If the system includes
a gauge, double check the gauge to assure
pressure has been released.
All Simplex cylinders and tools are equipped
with quick-disconnect couplings. These
couplings ease the assembly of your system.
These couplings must be assembled by
hand. Wrenches or pliers should not be
required for this operation.
If couplings will not fully engage (refer to
FIGURE 2 for proper engagement), turn the
release knob counter-clockwise to release
any pressure that may have built up.
Threaded connections such as fittings,
gauges, etc. must be securely tightened and
leak free. DO NOT over tighten connections.
Connections need only be secure and leak
free. Over tightening can cause premature
thread failure.
OSES H
S ON HOSE.
ssure
AUTION: Loose or cross threaded fittings
OPERATING INSTRUCTIONS
DO NOT DROP HEAVY OBJECT
A sharp impact may kink wire strands on which
the strength of the hose depends. AVOID
SHARP KINKS IN HOSE. Never apply pre
when hose is swung in sharp curves or when the
hose is visibly kinked.
C
can be potentially dangerous if pressurized.
Never hold or stand directly in line with any
hydraulic connections while pressurizing.
Never grab, touch or in any way come in
contact with a hydraulic pressure leak.
Escaping oil can penetrate the skin and a
serious injury can result.
1. Ope wise.
the
2. operate a single-acting cylinder,
own
3. wise until you
4. rvoir is full of
NECTED
5. on.
ENERAL MAINTENANCE
n the release knob counter-clock
Operate pump handle several times to
remove air from the system and to prime
pump.
You may
ram or tool with this style pump by merely
connecting the hose to the application.
Make sure you turn the cylinder upside d
to purge the air prior to use.
Close the release knob clock
hit a mechanical stop.
Be sure the pump rese
hydraulic oil. NEVER FILL THE
RESERVOIR UNLESS THE CON
application is FULLY RETRACTED.
Use the handle to advance your applicati
Be sure to take full strokes to get the optimal
flow rated for the pump in use.
G
The following
LUSHING THE PUMP:
eservoir, then
2. eservoir
3.
Change oil at least once a year.
conditions require more frequent oil changes:
F
1. Remove the old oil from the r
thoroughly clean the reservoir and refill with
a clean, nonflammable flushing oil.
Reassemble the pump head to the r
and pump the pump handle approximately
50 times with the RELEASE KNOB open.
Empty the reservoir, REPLACE GASKET,
and refill with clean SIMPLEX oil.
FILLER PLUG
LOC ATION
C LOSE / RELEASE
KNOB
PLUG LOC ATION
FIGURE 1
FIGURE 2