background image

2

 

 

 DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS
DAMAGED.

  Upon unpacking your Simplex product, inspect the contents of the

carton for shipping damage.  If damage is apparent, immediately file a claim
with the carrier and notify Simplex.

 
 
 ELECTRICAL HAZARD -

 Disconnect electrical power when making any

internal adjustments or repairs.  Servicing should be performed by qualified
Simplex Representatives.

 
 
 RADIO FREQUENCY ENERGY -

 This equipment generates, uses, and can

radiate radio frequency energy and if not installed and used in accordance with
the instruction manual, may cause interference to radio communications.  It has
been tested and found to comply with the limits for a Class A computing device
pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference when operated in a commercial
environment.  Operation of this equipment in a residential area may cause
interference in which case the user, at his own expense, will be required to take
whatever measures may be required to correct the interference.

 
EYE SAFETY HAZARD -

 Under certain application conditions, the optical

output of this device may exceed eye safety limits.  Do not use magnification
(such as a microscope or other focusing equipment) when viewing the output of
this device.

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Cautions and Warnings

 

 

 

firealarmresources.com

Содержание 4190-9011











Отзывы: