background image

14

6. o

PEraTing

 i

nSTrucTionS

 

 (cont.)

6.2 Polishing

a

Assemble the power tool for polishing.

s

Apply the least aggressive polish to the polishing pads.

3

Place the polishing pads face down on the test area 
(usually a 2x2’ spot) of the work surface. While in the 

OFF

 position, move the tool around to distribute the 

polish over the surface.

4

Hold the tool handle firmly by both hands and switch 
tool 

ON

.

5

Begin applying the polish over the work area with long 
sweeping strokes in a criss-cross pattern.

6

Work the polish in, using slow overlapping movements.

7

When the polish beaks down, remove residue, check 
work, repeat or go more aggressive (if needed) by using 
more aggressive polish.

k

After scratches/ swirls are removed or minimized, 
step down to a less aggressive polish to remove any 
hazing left from the more aggressive polishes. Repeat 
if necessary.

l

Once the desired finish is achieved, move on to the other 
sections of the work surface.

  IMPORTANT

 

Remember with polishing to BE PATIENT and learn how 
the polish works and breaks down and always start with 
the least aggressive pad/polish to get the job done.

 

By starting with a test section, it will allow you to see 
what polish is needed without going too aggressive or 
not aggressive enough to get the job done.

 

All polishes will go through stages as they break down. 
Each product is different, but basically their look goes 
from wet, hazing, translucent, to dry or oily. Without 
going through these stages you will not get the full effect 
of the polish and will most likely leave a hazed finish.

 

For more polishing details, see the instructions provided 
with your polish.

Preventing burning through paint

 

It is easy to burn through the paint on a surface, especially 
when working near edges or where there are abrupt changes 
in the contour of the work surface. This can occur if the 
polishing pads stay at one spot for a period of time.

 

To prevent burning through paint, keep the tool moving 
constantly.

Proper lighting

Without proper lighting, the majority of swirls and scratches are 
not visible. In addition, a lack of good lighting makes it very hard 
to see the polish breaking down, especially on light coloured cars. 
If possible, try to polish under controlled lighting. The sun can 
sometimes be masked by clouds, haze, or fog and can hide swirls, 
hazing and imperfections.

Operating Instructions

Содержание 039-6506-2



















Отзывы: