Simex SUR-457, Руководство пользователя

Страница: 54 / 62

User manual - METER SUR-457
Register Write Range Register description
A0h
1
Yes 0 ÷ 3
“ Omod ” parameter in “ OUtP ” menu (active current output mode)
0 - current output disabled ; 1 - current output enabled with 4 ÷ 20mA
mode; 2 - current output enabled with 0÷20mA mode ;
3 - current output controlled via RS-485 interface
Yes 0 ÷ 2
“ Omod ” parameter in “ OUtP ” menu (passive current output mode)
0 - current output disabled ; 1 - current output enabled with 4 ÷ 20mA
mode; 2 - current output controlled via RS-485 interface
Yes 0 ÷ 5
“ Omod ” parameter in “ OUtP ” menu (active voltege output mode)
0 - voltage output disabled ; 1 - voltage output enabled with 0 ÷5V
mode; 2 - voltage output enabled with 1÷5V mode ; 3 - voltage
output enabled with 0÷10V mode ; 4 - voltage output enabled with
2÷10V mode ; 5 - voltage output controlled via RS-485 interface
A1h 1 Yes -999 ÷ 9999 “ OUtL
” parameter in “
OUtP
” menu, no decimal point included
A2h 1 Yes -999 ÷ 9999 “ OUtH ” parameter in “ OUtP ” menu, no decimal point included
A3h 1
Yes 0 ÷ 999
“ Lo r ” parameter in “ OUtP ” menu, for active current output and
active voltage output, expressed in 0.1%
Yes 0 ÷ 299
“ Lo r ” parameter in “ OUtP ” menu for passive current output,
expressed in 0.1%
A4h 1
Yes 0 ÷ 199
“ Hi r ” parameter in “ OUtP ” menu for active and passive current
output, expressed in 0.1%
Yes 0 ÷ 99
“ Hi r ” parameter in “ OUtP ” menu for active voltage output,
expressed in 0.1%
A5h 1
Yes 0 ÷ 3
“ AL ” parameter in “ OUtP ” menu (active current output value on
critical exception): 0 - no change; 1 - 22.1 mA; 2 - 3.4 mA; 3 - 0 mA
Yes 0 ÷ 2
“ AL ” parameter in “ OUtP ” menu (passive current output value on
critical exception): 0 - no change; 1 - 22.1 mA; 2 - 3.4 mA
Yes 0 ÷ 5
“ AL ” parameter in “ OUtP ” menu (active voltage output value on
critical exception): 0 - no change; 1 - 11 V; 2 - 5.5; 3 - 1.2 V;
4
- 0.6 V;
5
- 0 V
1 - these registers are active only if device is equipped with current or voltage output
2 - after writing to register no 20h the device responds with an “old” address in the message.
3 - after writing to register no 22h the device responds with the new baud rate.
4 - the value of the “ mbAc ” parameter is also connected to write to this register, so it is possible to block a writes, but
impossible to unblock writes via RS-485 interface, The unblocking of the writes is possible from menu level only.
5 - the pairs of „ X - Y ” coordinates may be defined for any free point. The pair is “free” (it means that particular point is
not defined) if „ X ” coordinate of this point is equal 8000h. After writing both X and Y coordinate the point is defined
and used in calculation of result. The coordinates of any point can be changed at any time.
54