Simex STI-638 Скачать руководство пользователя страница 2

Страница: 2 / 52

CONTENTS

1. BASIC REQUIREMENTS AND USER SAFETY........................................................................................

2. GENERAL CHARACTERISTICS................................................................................................................

3. TECHNICAL DATA......................................................................................................................................

4. DEVICE INSTALLATION............................................................................................................................

4.1. UNPACKING.......................................................................................................................................

4.2. ASSEMBLY........................................................................................................................................

4.3. CONNECTION METHOD...................................................................................................................

4.4. MAINTENANCE................................................................................................................................

5. FRONT PANEL DESCRIPTION................................................................................................................

6. PRINCIPLE OF OPERATION...................................................................................................................

6.1. MEASUREMENT MODE..................................................................................................................

6.2. DETECTION OF THE PEAK VALUES............................................................................................

6.3. CONTROL OF THE RELAY OUTPUTS..........................................................................................

6.3.1. One threshold mode................................................................................................................

6.3.2. Two thresholds mode..............................................................................................................

7. DEVICE PROGRAMMING.........................................................................................................................

7.1. PROGRAMMING MENU..................................................................................................................

7.2. PARAMETERS EDITION.................................................................................................................

7.2.1. Numeric parameters (digit change mode)...............................................................................

7.2.2. Numeric parameters (slide change mode)..............................................................................

7.2.3. Switch parameters (“LIST” type).............................................................................................

7.3. MENU DESCRIPTION.....................................................................................................................

7.3.1. “rELAy1” menu........................................................................................................................

7.3.2. “bEEP” menu...........................................................................................................................

7.3.3. “inPUt” menu...........................................................................................................................

7.3.4. “FiLtEr” menu..........................................................................................................................

7.3.5. ”OutPUt” menu........................................................................................................................

7.3.6. “briGHt” parameter..................................................................................................................

7.3.7. “HOLd” menu...........................................................................................................................

7.3.8. ”SECU” menu..........................................................................................................................

7.3.9. “rS-485” menu.........................................................................................................................

7.3.10. “Edit t” parameter..................................................................................................................

7.3.11. “dEFS” parameter..................................................................................................................

7.3.12. “SErv” menu..........................................................................................................................

7.4. MENU STRUCTURE........................................................................................................................

8. EXAMPLES OF “MUL” AND “DIV” PARAMETERS CALCULATION...................................................

9. OUTPUT VALUE CALCULATION............................................................................................................

10. THE MODBUS PROTOCOL HANDLING...............................................................................................

10.1. LIST OF REGISTERS....................................................................................................................

10.2. TRANSMISSION ERRORS DESCRIPTION..................................................................................

10.3. EXAMPLES OF QUERY/ANSWER FRAMES...............................................................................

11. DEFAULT AND USER'S SETTINGS LIST.............................................................................................

Содержание STI-638





















































Результаты поиска

Содержание STI-638

Отзывы:

Похожие инструкции для STI-638

Бренды по названию

Популярные бренды

Simex STI-638, Руководство пользователя

Результаты поиска

Содержание STI-638

Отзывы:

Похожие инструкции для STI-638

Бренды по названию

Популярные бренды