Sime MURELLE HE 110 R ErP, Оригинальное руководство пользователя

Страница: 74 / 88

74
NOTE: the inside of the upper door of the
boiler panel has a label with the values
that have to be set for PAR 1 and PAR 2
(fig. 19).
3.3.2 Warning
Should the boiler operation not be optimal
but no alarm sets off, press the button
5
3
1
2
4
until info 70 and the warning code
associated to the ongoing event are displa-
yed.
Once optimal operation is restored, info 70
will display: “- -”.
Below is the table of warning codes:
PARAMETERS INSTALLER
EXPANSION CARD
PAR DESCRIPTION RANGE UNIT OF INC/DEC DEFAULT
MEASUREMENT UNIT SETTING
40 Number of expansion boards 0 ... 3 = 1 0
41 Mix valve stroke time 0 ... 199 10 sec. 1 12
42 Priority of D.H.W. over mixed zone 0 = Paralle = = 1
1 = Absolute
43 Floor drying 0 = No activated = = 0
1 = Curve A
2 = Curve B
3 = Curve A+B
44 Type of solar system 1 ... 8 = 1 1
45
∆
t solar collector pump 1 PAR 74 OEM - 1... 50 °C 1 8
46 Solar integration delay “--”, 0 ... 199 Min. 1 0
47 Tmin solar collector “--”, -30 ... 0 °C 1 - 10
48 Tmax solar collector “--”, 80 ... 199 °C 1 120
PARAMETERS RESTORATION
PAR DESCRIPTION RANGE UNIT OF INC/DEC DEFAULT
MEASUREMENT UNIT SETTING
49 * Reset default parameters -- , 1 = = =
(par 01 - par 02 = “-“)
* In case of difficulty in understanding the current setting or in case of an anomalous or
incomprehensible conduct of the boiler, we suggest to restore the initial values of the parameters
setting PAR 49 = 1 and the PAR 1 and PAR 2 as specified at point 3.3.1.
CASCADE CONNECTION PARAMETERS
When the appliance is installed in sequence/cascade (modular
system with several generators) it is necessary to set on all the
boilers the following INST PAR parameters:
PAR 15 = 0 for the first boiler (MASTER)
1 .... 7 for the other boilers (SLAVE)
(Avoid assigning the same number to SLAVE boilers)
WARNING: Before modifying parameter “PAR 15” (cascade
address assignment) the boilers present in cascade must be acti-
vated in WINTER mode
Set the following INST parameter if polypropylene smoke collec-
tors with a clapet valve are used in sequence/cascade installa-
tions:
PAR 1 = 69 (for NATURAL GAS boilers)
71 (for PROPANE boilers)
In addition, when the number of boilers in cascade is more than
two, configure the parameters OEM A1 of the MASTER boiler.
To access the OEM parameters press simultaneously the buttons
(
5
3
1
2
4
and
5
3
1
2
4
) for 2 seconds.
Entered in the INST level again press simultaneously he buttons (
5
3
1
2
4
and
5
3
1
2
4
) for another 2 seconds. At this point insert the access
code formed by this sequence of INSTALLATOR BUTTONS: “ + / - /
< / > / < “.
Set the parameter:
PAR A1 = Number of cascade generators (3 ... 8)
CODE DESCRIPTION
E0
Reduced capacity operation
(
∆
t between delivery and return
over 40°C)
E1
Shorted external sensor (SE)
E2
Preheating function active
E3
TBD
E4
TBD
E5
TBD
E6
TBD
E7
TBD
E8
TBD
E9
TBD
BOILER PAR 2
Instant with deviator valve
1
and flowmeter
Instant with deviator valve,
2
flowmeter and solar combination
D.H.W. tank with
deviator valve and boiler sensor
3
vers. T (LOW INERTIA)
On board D.H.W. tank with
deviator valve and D.H.W. sensor
4
(LOW INERTIA)
Remote D.H.W. tank with deviator
valve and D.H.W. thermostat
5
or heating only vers. T/R boiler
(LOW INERTIA)
On board D.H.W. tank with
double pump and D.H.W. sensor
6
vers. T/R boiler
(LOW INERTIA)
On board D.H.W. tank with
double pump and D.H.W.
thermostat vers. T/R boiler
8
(LOW INERTIA)
Heating only with
antifreeze sensor
9
(LOW INERTIA)