Sime Ecomfort Plus Скачать руководство пользователя страница 6

6

1.6.2

Temperature/pressure gauge

The gauge (A fig. 1) on the facia panel indicates the approxi-
mate  system  pressure.  The  normal  operating  pressure  is
between  1  and  1.5  bar.  If  the  normal  running  pressure  is
seen to decrease over a period of time there is a water leak
and you should consult your installer or service engineer. 

1.6.3

Electrical supply

The  mains  plug  used  must  be  a  3  pin  type  to  BS1363,  and
fused at 3 A. THIS APPLIANCE MUST BE EARTHED.

NOTE: 
an  interruption  in  the  electricity  supply  whilst  the  burner
is alight may cause the overheat thermostat to operate. If
this  is  suspected,  turn  the  rotary  switch  to  “

“  position,

then turn it back to the previous position.

TO CONNECT A PLUG

As the colour of wires in the mains lead of this appliance may
not  correspond  with  the  coloured  markings  identifying  the
terminals in your plug, proceed as follows:
the  wire  which  is  coloured  green  and  yellow  must  be  con-
nected  to  the  terminal  in  the  plug  which  is  marked  with  the
letter  E  or  by  the  earth  symbol  -  or  coloured  green  and  yel-
low;  the  wire  which  is  coloured  blue  must  be  connected  to
the terminal marked with the letter N or coloured black; the
wire which is coloured brown must be connected to the ter-
minal marked with the letter L or coloured red.

1.6.4

Ventilation

If the appliance is installed in a cabinet, the latter MUST NOT

be  used  for  storage  purposes.  Any  ventilation  provided  for
the appliance during installation MUST NOT be blocked and a
periodic  check  must  be  made  to  ensure  that  the  vents  are
free from obstructions.

1.6.5

Cleaning

Use only a damp cloth and mild detergent to clean the appli-
ance outer casing. DO NOT use abrasive cleaners.

1.7

SAFETY

It is essential that the instructions in this booklet are strict-
ly  followed  for  the  safe  and  economical  operation  of  this
appliance.  The  appliance  functions  as  a  fan  assisted  bal-
anced flue unit. 
The flue terminal MUST NOT BE OBSTRUCTED under any cir-
cumstances.  If  damaged,  turn  off  the  appliance  and  consult
the installer, service engineer, or gas supplier. If it is known or
suspected  that  a  fault  exists  on  the  appliance  it  MUST NOT
be used until the fault has been rectified by a competent per-
son.

WARNING:  IF  A  GAS  LEAK  IS  SUSPECTED  OR  EXISTS,
TURN  OFF  THE  GAS  SUPPLY  TO  THE  APPLIANCE  AT  THE
GAS  SERVICE  COCK.  DO  NOT  OPERATE  ANY  ELECTRICAL
SWITCHES.  DO  NOT  OPERATE  ANY  ELECTRICAL  APPLI-
ANCE.  OPEN  ALL  WINDOWS  AND  DOORS.  DO  NOT
SMOKE.  EXTINGUISH  ALL  NAKED  LIGHTS.  CONTACT  THE
GAS SUPPLIER IMMEDIATELY.

Содержание Ecomfort Plus













Отзывы: