background image

 

                                                                         6

drop the load. See instruction 3 page 7. 
5. Select the lifting point on the fork lift with care. It must be strong 

enough to resist the lifting force without damaging the fork lift. It is 
desirable to cradle the lifting point in the arm notch when 
possible(See Fig.1-B). 

 
 
 
6. Use only the serrated lifting 

pad, or the notch at the end of 
the lifting arm as the lifting 
contact. Do not attempt to use 
any other part of the 

HFJ-400 

lack as a lifting contact point.    

 
 
 

 

 
                                                                     
7. Raise a fork lift with the 

HFJ-400 

only when: 

a. The forks are in a lowered position 
b. There is no load of any kind on the forks 
c. There are no personnel on the jacks  

 
 
 
 
 
 
 
8. If the fork lift truck is to be lifted, lowered and relifted, the following 

procedure is to be followed. 

a. Lift and lower in accordance with the instructions in this manual 
b. Before using a second jack, make certain that the jack is 

replaced in full accordance with the initial instructions in this 
manual. (See Paragraph 4 of Operating Instructions)  

 

 

Fig.5

Содержание HFJ-400















Отзывы: