General Safety
Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
Keep guards in position
Always keep guards in position, in good working order, correctly adjusted
•
and aligned. Never attempt to use a tool if any of the supplied guards are
missing. If any guards are damaged, replace before use.
Remove adjusting keys
Always check to see that keys and adjusting devices are removed from
•
the tool before use.
Clean the work area
Accidents can occur where benches and work areas are cluttered or
•
dirty, floors must be kept clear, avoid working where the floor is slippery.
If working outdoors, make yourself aware of all potential slip and trip
hazards before using this tool.
Children and pets
Children and pets should always be kept at a safe distance from your
•
work area. Lock tools away where children can not get access to them.
Do not allow children, or untrained persons to use this tool.
Use the correct tool
Do not force, or attempt to use a tool for a purpose it was not designed.
•
This tool is not intended for industrial use.
•
Wear suitable clothing and footwear
Do not wear loose fitting clothing, neckties, jewellery, or other items
•
which may become caught. Wear non-slip footwear with protective toe
caps where appropriate. Long hair should be covered or tied back.
Keep your balance
Do not over reach, keep proper footing at all times, do not use tools when
•
standing on an unstable surface.
Accessories
The use of any attachment or accessory, other than those mentioned in
•
this manual, could be dangerous and result in damage or injury, and may
invalidate your warranty.
Never stand on your tool
Standing on your tool or its stand could cause serious injury if the tool
•
is tipped or collapses. Do not store materials above or close to the tool
in such a way that a person might stand on the tool to reach the stored
items.
Secure work
Where possible, always secure work. If appropriate use a clamp or vice, it
•
will allow you to use both hands to operate your tool.
Check for damaged or missing parts
Before each use, check if any part of the tool is damaged or missing,
•
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre.
DO NOT USE IF DEFECTIVE.
4
GB
Specification
Power: ..................................................14.4Vd.c-1.5Ah
No load speed: .....................................0-900min
-1
Impact rate:..........................................0-4800BPM
Impact energy ......................................1.1J
Max drilling capacity:
-Concrete............................................ 10mm
-Wood..................................................16mm
-Steel...................................................8mm
Weighted vibration: ..............................5.915m/s²
Uncertainty:..........................................1.5m/s
2
Sound pressure: ...................................80.5dB(A)
Sound power: .......................................91.5dB(A)
Uncertainty ...........................................3dB(A)
Protection Class:...................................
Battery charger
Input: .................................................... 220-240V AC.
50/60Hz, 17W
Output: .................................................18V DC, 400mA
The sound intensity level for the operator may exceed
85dB(A) and sound protection measures are necessary.
As part of our ongoing product development,
specifications of Silverline products may alter without
notice.
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
Separated or safety extra-low voltage.
Conforms to relevant legislation and safety standards.
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
878973_Z1MANPRO1.indd 4
17/1/11 10:34:24
