background image

IT

28

ATTENZIONE:

 Indossare sempre protezioni per le orecchie, quando il livello sonoro supera i 85 dB 

(A) e limitare il tempo di esposizione, se necessario . Se i livelli sonori diventano sgradevoli, anche 

con la protezioni per le orecchie, smettere di usare lo strumento immediatamente e controllare 

che la protezione acustica sia montata correttamente e che fornisca il corretto livello di isolamento 

acustico per il livello del suono prodotto dal vostro strumento .

ATTENZIONE:

 L'esposizione dell'utente alle vibrazioni dell’utensile  può causare la perdita del  

senso del tatto, intorpidimento, formicolio e riduzione della capacità di presa. Una lunga 

esposizione può portare ad una condizione cronica. Se necessario, limitare la durata di esposizione 

alle vibrazioni e utilizzare guanti anti-vibrazione. Non utilizzare l’utensile se la temperatura delle 

mani è al di sotto del normale, in quanto ciò farà sì che l’effetto delle vibrazioni sia maggiore. 

Utilizzare i dati forniti nella specifica relativa alle vibrazioni per calcolare la durata e la frequenza di 

funzionamento dello strumento .
I livelli sonori e le vibrazioni nella specifica sono determinati secondo la EN60745 o simili standard 

internazionali. Le figure rappresentano un normale utilizzo per lo strumento in normali condizioni 

di lavoro . Un utensile tenuto in cattive condizioni, montato in modo errato o utilizzato in maniera 

impropria può essere causa di un aumento dei livelli sonori e delle vibrazioni.  

www.osha.europa.eu

 fornisce informazioni sui livelli sonori e delle vibrazioni nei luoghi di  

lavoro utili agli utenti domestici che utilizzano utensili per lunghi periodi di tempo .

Norme generali di sicurezza

 

AVVERTENZA: Leggere ed assimilare tutte le istruzioni.

 La non osservanza delle seguenti 

istruzioni può causare scosse elettriche, incendi e/o lesioni gravi.

Conservare tutte le avvertenze di pericolo e le istruzioni operative per ogni esigenza futura.

Il termine “elettroutensile” si riferisce all’utensile a rete fissa (con filo) o un utensile a  

batteria (senza filo).

1)  Sicurezza nell’area di lavoro.
a)  Mantenere l’area di lavoro pulita e adeguatamente illuminata. 

Il disordine e le zone di  

  lavoro non illuminate possono essere fonte di incidenti.

b)  Non usare gli elettroutensili in presenza di atmosfere esplosive, come liquidi, gas e  

  polveri infiammabili. 

Gli elettroutensili producono scintille che potrebbero accendere le  

  polveri o i fumi.

Traduzione delle istruzioni originali

Abbreviazioni tecniche

Descrizioni dei simboli

La targhetta sul vostro utensile può mostrare simboli. Questi rappresentano informazioni importanti 

riguardanti il prodotto o istruzioni sul suo utilizzo .

Indossare la protezione acustica

Indossare occhiali di protezione

Indossare una protezione per la respirazione

Indossare il casco

Indossare la protezione delle mani

Leggere il manuale di istruzioni

Conforme alle normative pertinenti e gli standard di sicurezza

Fumi o gas tossici!

Costruzione di classe II (doppio isolamento per conferire una protezione ancora 

maggiore)

Protezione ambientale

 

I rifiuti di prodotti elettrici non devono essere smaltiti con i rifiuti domestici. Nel caso 

in cui esistano strutture, provvedere al riciclaggio. Verificare con le autorità locali o il 

rivenditore per consigli sul riciclaggio

V

Volt

~, AC

Corrente alternata

A, mA

Ampere, milliampere

n0

Velocità in assenza di carico

opm

Orbite od oscillazioni al minuto

°

Gradi

Ø

Diametro

W, kW

Watt, kilowatt

/min or min

-1

Operazioni al minuto

dB(A)

Livello sonoro in decibel (A ponderato)

  

 

 

Tensione in ingresso   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .230-240 V~
Potenza   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 300 W
Velocità in assenza di carico   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .10 .000-22 .000 opm
Classe di protezione .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  
Protezione ingresso  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .IP20
Peso  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1,5 kg

Come parte del nostro continuo sviluppo dei prodotti, le specifiche  

dei prodotti Silverline possono variare senza preavviso .

Informazioni sul suono e sulle vibrazioni:

Pressione sonora L

PA

 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 86,3 dB(A)

Potenza sonora L

WA

 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 97,3 dB(A)

Incertezza K .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3 dB(A)

Il livello di intensità del suono per l'operatore può superare i 85 dB (A)  

e le misure di protezione del suono sono necessari .

Introduzione

Grazie per aver acquistato questo utensile Silverline. Queste istruzioni contengono informazioni 

utili per il funzionamento sicuro ed affidabile del prodotto.  Per  essere sicuri di utilizzare al meglio 

il potenziale dell’utensile si raccomanda pertanto di leggere a fondo questo manuale. Conservare il 

manuale in modo che sia sempre a portata di mano e accertarsi che l’operatore dell’elettroutensile 

lo abbia letto e capito a pieno. 

Specifiche tecniche

430787_MANUAL.indd   28

09/05/2017   16:27

Содержание DIY 430787















































Отзывы: