20 GB/IE
battery compartment cover
8
onto the battery
compartment
13
until you hear it lock into place.
5. Tighten the screw by using a scewdriver
(see Fig. B).
Q
Replacing the battery
1. Switch off the kitchen scale
2
. Press and hold
down the On / Off / Zero button
5
for 3 seconds.
2. Loosen the screw located at the back of the
kitchen scale
2
by using a screwdriver. Open
the battery compartment
13
as described above.
3. Remove the exhausted batteries from the battery
embedding case
11
by pressing and pulling
the black battery locking tab
12
. The battery is
automatically released from the battery embed-
ding case
11
. Ensure that you do not exert too
much force on the battery metal contact
10
,
otherwise it could be damaged by over-bending
as the battery is lifted. Remove the battery from
the battery embedding case
11
.
4. Insert a new battery into the battery embedding
case
11
. Make sure you fit the battery the right
way round (polarity). The “+”- side must face
upwards. The battery must be pressed inside
the battery embedding case
11
.
5. Close the battery compartment
13
and tighten
the screw by using a screwdriver.
Q
Unit conversion button
The g / lb:oz unit conversion button
9
for the
units of weight can be found on the bottom of
the kitchen scale
2
. By simply pressing the
button the units of measure change between
metric (g, ml) and imperial (lb:oz, fl’oz).
Note:
– If the units of weight are set to metric (g) then the
units of volume will be automatically shown as ml.
– If the units of weight are set to imperial (lb:oz)
then the units of volume will be automatically
shown as fl’oz.
– The standard unit of weight is g.
Q
Weighing
Note:
Starting with or without the weighing bowl
1
,
the kitchen scale
2
always starts from 0 g /
0:0.0 lb:oz
16
/
19
if the On / Off / Zero button
5
is pressed.
If you place the weighing bowl
1
on the kitchen
scale
2
after it has been switched on, then the dis-
play will show the weight of the weighing bowl
1
.
Press the On / Off / Zero button
5
once to reset the
display to 0 g / 0:0.0 lb:oz
16
/
19
, “T“ (TARE)
25
shows on the LC display
4
.
Place the kitchen scale on a solid, flat surface.
Press the On / Off / Zero button
5
to switch
on the kitchen scale
2
(see Fig. C).
Wait until the LC display
4
stops and stabilizes
on 0 g
16
, 0:0.0 lb:oz
19
or 0 ml
17
or 0.0 fl’oz
18
, which will be the mode the kitchen scale
was in when it was last switched off.
Press the mode setting button
3
to set the
kitchen scale to the normal weighing mode
22
.
If necessary select the units of weight in ad-
vance by pressing the g / lb:oz unit conversion
button
9
on the bottom of the kitchen scale
before you start weighing.
For re-calibrating the kitchen scale
2
, when
you have selected the units of weight press and
hold down the On / Off / Zero button
5
for 3
seconds to switch off the kitchen scale
2
.
Stand the kitchen scale
2
on a hard, flat table
surface. Place the weighing bowl
1
on the
weighing platform
6
.
Press the On / Off / Zero button
5
to switch on
the kitchen scale in the normal weighing mode.
Wait until all the segments of the LC display
4
have illuminated and the kitchen scale
2
has
stabilized at 0 g
16
, 0:0.0 lb:oz
19
.
Place the substance to be weighed into the
weighing bowl
1
to start the weighing process.
The LC display
4
shows the weight of the sub-
stance in the weighing bowl
1
in the selected
unit of weight (see Fig. D).
