manualshive.com logo in svg

Silicon Laboratories WGM160P, Руководство пользователя, Страница: 29 / 35

Поделиться
Скачать
Silicon Laboratories WGM160P Скачать руководство пользователя страница 29

9.2  Debug Modes

Programming external devices is done by connecting to a target board through the provided debug connector and by setting the debug
mode to [

Out

]. The same connector can also be used to connect an external debugger to the WGM160P Wi-Fi Module on the kit by

setting debug mode to [

In

].

Selecting the active debug mode is done in Simplicity Studio.

Debug MCU:

 In this mode, the on-board debugger is connected to the WGM160P on the kit.

RADIO BOARD

Board

Controller

USB

Host

Computer

DEBUG HEADER 

External

 Hardware

Figure 9.1.  Debug MCU

Debug OUT:

 In this mode, the on-board debugger can be used to debug a supported Silicon Labs device mounted on a custom board.

Board

Controller

USB

Host

Computer

DEBUG HEADER 

External

 Hardware

RADIO BOARD

Figure 9.2.  Debug OUT

Debug IN:

 In this mode, the on-board debugger is disconnected, and an external debugger can be connected to debug the WGM160P

on the kit.

Board

Controller

USB

Host

Computer

DEBUG HEADER 

External Debug Probe

RADIO BOARD

Figure 9.3.  Debug IN

UG351: WGM160P Wi-Fi Module Wireless Starter Kit User's Guide

On-Board Debugger

silabs.com

 | Building a more connected world.

Rev. 1.0  |  29

Содержание WGM160P




































Отзывы:

Нет отзывов