manualshive.com logo in svg

Silicon Laboratories WGM160P, Руководство пользователя, Страница: 16 / 35

Поделиться
Скачать
Silicon Laboratories WGM160P Скачать руководство пользователя страница 16

5.  Peripherals

The starter kit has a set of peripherals that showcase some of the features of the WGM160P.

Be aware that most WGM160P I/O routed to peripherals are also routed to the breakout pads or the EXP header. This must be taken
into consideration when using these.

5.1  Push Buttons and LEDs

The kit has two user push buttons marked PB0 and PB1. They are connected directly to the WGM160P and are debounced by RC
filters with a time constant of 1 ms. The buttons are connected to pins PD6 and PD8.

The kit also features two yellow LEDs marked LED0 and LED1 that are controlled by GPIO pins on the WGM160P. The LEDs are con-
nected to pins PA4 and PA5 in an active-high configuration.

PA5 (GPIO)

User Buttons 

& LEDs

UIF_LED0

UIF_LED1

UIF_PB0

UIF_PB1

PD6 (GPIO)

PD8 (GPIO)

PA4 (GPIO)

WGM160P

Figure 5.1.  Buttons and LEDs

UG351: WGM160P Wi-Fi Module Wireless Starter Kit User's Guide

Peripherals

silabs.com

 | Building a more connected world.

Rev. 1.0  |  16

Содержание WGM160P




































Отзывы:

Нет отзывов