background image

Simplicity Studio

One-click access to MCU and 
wireless tools, documentation, 
software, source code libraries & 
more. Available for Windows, 
Mac and Linux!

IoT Portfolio

www.silabs.com/IoT

SW/HW

www.silabs.com/simplicity

Quality

www.silabs.com/quality

Support and Community

community.silabs.com

http://www.silabs.com

Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA

Disclaimer

Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or 
intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" 
parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes 
without further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. 
Without prior notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons.  Such changes will not alter the specifications or the 
performance of the product.  Silicon Labs shall have no liability for the consequences of use of the information supplied in this document. This document does not imply or expressly grant 
any license to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket 
approval is required or Life Support Systems without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or 
health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon 
Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering 
such weapons. Silicon Labs disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such 
unauthorized applications.

Trademark Information

Silicon  Laboratories  Inc.®  ,  Silicon  Laboratories®,  Silicon  Labs®,  SiLabs®  and  the  Silicon  Labs  logo®,  Bluegiga®,  Bluegiga  Logo®,  Clock

B

uilder®,  CMEMS®,  DSPLL®,  EFM®, 

EFM32®,  EFR,  Ember®,  Energy  Micro,  Energy  Micro  logo  and  combinations  thereof,  "the  world’s  most  energy  friendly  microcontrollers",  Ember®,  EZLink®,  EZRadio®,  EZRadioPRO®, 
Gecko®, Gecko OS, Gecko OS Studio, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® , Zentri, the Zentri logo and Zentri 
DMS,  Z-Wave®, and others are trademarks or registered trademarks of Silicon Labs.  ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. 
Keil is a registered trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance.  All other products or brand names mentioned herein are trademarks of their respective 
holders.

Содержание SLWRB4202A




































Отзывы: