manualshive.com logo in svg

Silicon Laboratories SLWRB4150A, Руководство пользователя

Поделиться
Скачать
Silicon Laboratories SLWRB4150A Скачать руководство пользователя страница 11

5.2  Board Controller Power

The  board  controller  is  responsible  for  important  features  such  as  the  debugger  and  the  Advanced  Energy  Monitor,  and  is  powered
exclusively through the USB port in the top left corner of the board. This part of the kit resides on a separate power domain, so a differ-
ent power source can be selected for the target device while retaining debugging functionality. This power domain is also isolated to
prevent current leakage from the target power domain when power to the Board Controller is removed.

The board controller power domain is exclusively supplied by the J-Link USB cable, and is not influenced by the position of the power
switch.

The kit has been carefully designed to keep the board controller and the target power domains isolated from each other as one of them
powers down. This ensures that the target EFR32 device will continue to operate in the 

USB

 and 

BAT 

modes.

5.3  EFR32 Reset

The EFR32 Wireless SoC can be reset by a few different sources:

• A user pressing the RESET button.
• The on-board debugger pulling the #RESET pin low.
• An external debugger pulling the #RESET pin low.

In  addition  to  the  reset  sources  mentioned  above,  the  Board  Controller  will  also  issue  a  reset  to  the  EFR32  when  booting  up.  This
means that removing power to the Board Controller (plugging out the J-Link USB cable) will not generate a reset, but plugging the cable
back in will, as the Board Controller boots up.

UG178: EFR32MG 2400/868 MHz 13 dBm Dual Band Radio Board

Power Supply and Reset

silabs.com

 | Smart. Connected. Energy-friendly.

Rev. 1.00  |  10

Содержание SLWRB4150A
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды