manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание


Поделиться
Скачать
background image

Chapter 8: Using the Synchronous Mirroring Premium Feature

155

Snapshot (Legacy) 
Volumes

A snapshot (legacy) is a point-in-time image of a volume. Typically, it is created so 

that an application, such as a backup application, can access the snapshot (legacy) 

volume and read the data while the base volume stays online and is accessible to 

hosts. 
The volume for which the point-in-time image is created is known as the base volume 

and must be a standard volume in the storage array. The snapshot (legacy) repository 

volume stores information about all data that changed since the snapshot (legacy) was 

created. 
In this version of the storage management software, you can create snapshot (legacy) 

volumes based on the primary volume or secondary volume of a remote mirror.

Volume Copy

The Volume Copy premium feature copies data from one volume (the source volume) 

to another volume (the target volume) within a single storage array. You can use this 

premium feature to perform these functions:

Copy data from volume groups that use smaller-capacity drives to volume groups 

that use larger-capacity drives

Back up data

Restore snapshot (legacy) volume data to the base volume.

You can use a primary volume in a remote mirror as a source volume or a target 

volume in a volume copy. You cannot use a secondary volume as a source volume or a 

target volume.

NOTE  

If you start a role reversal during a copy-in-progress, the copy fails and cannot 

be restarted.

Dynamic Volume 
Expansion

A Dynamic Volume Expansion (DVE) is a modification operation that increases the 

capacity of a standard volume or a snapshot (legacy) repository volume. The increase 

in capacity is achieved by using the free capacity that is available in the volume group 

of the standard volume or the snapshot (legacy) repository volume.
This modification operation is considered to be “dynamic” because you can 

continually access data on volume groups, volumes, and drives throughout the entire 

operation.
A DVE operation can be performed on a primary volume or a secondary volume of a 

mirror relationship. 

NOTE  

Although the storage management software indicates that the volume has 

increased capacity, its usable capacity is the size of the smaller of the primary volume 

or the secondary volume.

You cannot perform a DVE operation on a mirror repository volume.

Содержание InfiniteStorage 4000 Series





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage 4000 Series

Mercusys MR30G Quick Installation Manual preview
MR30G
Бренд: Mercusys Страницы: 35
BSD Networks bsg-0800t User Manual preview
bsg-0800t
Бренд: BSD Networks Страницы: 7
Shenzhen JingFeng HDM-05 User Manual preview
HDM-05
Бренд: Shenzhen JingFeng Страницы: 11
POCKetec POCKEY User Manual preview
POCKEY
Бренд: POCKetec Страницы: 19
TP-Link TL-SL2226P+ User Manual preview
TL-SL2226P+
Бренд: TP-Link Страницы: 37
Sollae Systems CSE-H20 User Manual preview
CSE-H20
Бренд: Sollae Systems Страницы: 45
Kramer VS-162AVM User Manual preview
VS-162AVM
Бренд: Kramer Страницы: 56
Kasda KE318EU User Manual preview
KE318EU
Бренд: Kasda Страницы: 39
IBM Travelstar 14GS Quick Installation Manual preview
Travelstar 14GS
Бренд: IBM Страницы: 2
ACTi ACD-2000Q Quick Installation Manual preview
ACD-2000Q
Бренд: ACTi Страницы: 11
SilverStone TOWER STORAGE TS421S Manual preview
TOWER STORAGE TS421S
Бренд: SilverStone Страницы: 52
Netberg Aeon J460 M2 JBOD Manual preview
Aeon J460 M2 JBOD
Бренд: Netberg Страницы: 67
Ravpower Power 7 Wi-Fi SD/USB Storage kit User Manual preview
Power 7 Wi-Fi SD/USB Storage kit
Бренд: Ravpower Страницы: 60
Seagate Barracuda 36ES2 ST318418N Installation Manual preview
Barracuda 36ES2 ST318418N
Бренд: Seagate Страницы: 2
ABB MC502 Installation Instructions preview
MC502
Бренд: ABB Страницы: 2
GE AccessPoint 001890 User Instructions preview
AccessPoint 001890
Бренд: GE Страницы: 2
GE Digital Video Storage System User Manual preview
Digital Video Storage System
Бренд: GE Страницы: 24
GE Monogram ZWVS1000SR Owner'S Manual preview
Monogram ZWVS1000SR
Бренд: GE Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды