background image

 

 

Silicon CPV plc 

Akhter House, Perry Road, Harlow, Essex, CM18 7PN, UK  

Tel +44 (0) 1279 821200 Email [email protected] 

Page 1 of 32 

 

Contents 

Document Revision Control ................................................................ 2

 

Disclaimer ....................................................................................... 3

 

Unpacking - Box Contents ................................................................. 3

 

Badr 1/2+G2 ................................................................................. 3

 

Kamr+G2 Range ............................................................................ 3

 

Booster Pack .................................................................................... 4

 

Tools Required for Installation and Maintenance ................................... 5

 

Key Solar Street Light Components ..................................................... 6

 

Kamr ............................................................................................ 6

 

Badr ............................................................................................. 6

 

Available Model Numbers with Optical Lens Options .............................. 7

 

Theory of Operation .......................................................................... 8

 

Installation Instructions for Kamr – Part 1 ......................................... 10

 

Mode selection ............................................................................. 10

 

Antenna Installation ..................................................................... 11

 

Installation Instructions for Kamr – Part 2 ......................................... 12

 

Fixing the Solar Street Light to the Pole .......................................... 12

 

Pole Sizing and Spacing for Kamr ..................................................... 13

 

Installation Instructions for Badr – Part 1 .......................................... 14

 

Battery Bank and Controller Access ................................................ 14

 

Installation Instructions for Badr – Part 2 .......................................... 15

 

Mode selection ............................................................................. 15

 

Installation Instructions for Badr – Part 3 .......................................... 16

 

Fixing the Solar Street Light to the Pole .......................................... 16

 

Pole Sizing and Spacing for Badr ...................................................... 17

 

Optical Lens and Distribution Patterns ............................................... 18

 

Network Management and Monitoring ............................................... 20

 

Maintenance and Care of Solar Lights ................................................ 21

 

Troubleshooting ............................................................................. 22

 

Содержание Badr 1+G2


































Отзывы: