background image

-13- 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

MAN 

 

With the selector switch in the Manual, Alert or Hands Free position this 

momentary push-button switch provides a manually activated Wail siren tone.  
While the selector switch is in the Wail, Yelp, or Phaser position, this switch 
provides a generally quicker changing tone.  (See tables below and on next page). 
These quicker tones are used to momentarily alert motorists at intersections and 
very highly congested areas.  Pressing the button once changes to the next faster 
tone.  Pressing the manual button again, reverts the siren back to the original tone.   
 
 

Optional configuration allows the replacement of the Phaser tone with Two -

Tone, or the disabling the Phaser tone entirely.  These options are selected during 
installation and may be governed by State or Local laws.  (Refer to the 
INSTALLER SELECTABLE OPTIONS section on page 4). 
 
 
 

HORN (Air Horn) 

 

This momentary push-button switch provides a simulated air -horn tone while 

pressed.  This can be used to either replace, or to supplement the normal vehicle 
horn and is useful at intersections or in low noise areas.  This tone will override all 
other siren tones.

 

 

 
 
 
 
 
 
 
 
 
 

Содержание SS730





















Отзывы: