manualshive.com logo in svg

SIGNAL FIRE GWDIN, Инструкция по интерфейсу

Поделиться
Скачать
SIGNAL FIRE GWDIN Скачать руководство пользователя страница 5

 

Rev 1.15

 

SignalFire Telemetry

 

 

5

 

Connections and Components

 

 

DIN Gateway Connections

 

The DIN Gateway has a 6-position pluggable terminal block for power and serial 
communications. The connections are as follows:

 

 

Terminal Name

 

Connection

 

6-36VDC (RED)

 

Positive Power (6 to 36 VDC)

 

GROUND (BLK)

 

Ground

 

RS232 TX (ORG)

 

RS-232 Debug TX, 9600 Baud (Only used with Ethernet Interface module)

 

RS232 RX (YEL)

 

MODBUS A (GRN)

 

RS-232 Debug RX, 9600 Baud (Only used with Ethernet Interface module)

 

RS-485 “A”, 9600 Baud

 

MODBUS B (BRN)

 

RS-485 “B”, 9600 Baud

 

In addition, a RS232 DB9 port is available for connection to the SignalFire Toolkit for configuration 
and diagnostics.  

Gateway Hardware revision 2 also has a 3-position pluggable terminal block with two open collector 
digital outputs for signaling or alarm functions.  Each output is rated to 30VDC and 1 Amp.   

 

Optional Ethernet Gateway Connections

 

When used with a SignalFire Ethernet Interface Module, the 6-potition screw terminal block should be 
connected to the color coded “Gateway Stick Connection” connector on the Ethernet Interface 
Module.  Power can be supplied either to the Power Input terminals on the Ethernet Interface Module 
or via power over Ethernet (PoE). For more information on configuring and using the Ethernet 
Interface Module, please consult the Ethernet Interface Module manual.

 

 

NOTE:  when used with an Ethernet Interface Module the DB9 on the Ethernet module must be used for 
ToolKit access. 

 

 

 

 

 

 

 

Содержание GWDIN


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды