manualshive.com logo in svg

SIGNAL FIRE GWDIN, Инструкция по интерфейсу, Страница: 31 / 33

Поделиться
Скачать
SIGNAL FIRE GWDIN Скачать руководство пользователя страница 31

 

Rev 1.15

 

SignalFire Telemetry

 

 

31

 

Revision History

 

 

 

Revision

 

Date

 

Changes/Updates

 

1.0

 

10/02/15

 

Initial Release for DIN Gateway

 

1.1

 

2/26/16

 

Added FCC/IC certification details

 

1.2

 

4/6/16

 

Added detail for Gateway digital outputs 

 

1.4/1.5

 

4/18/16

 

Updated IC statements and added C1D2 Statements

 

1.6

 

8/3/16

 

Added section on encryption 

 

1.7/1.8

 

9/4/2018

 

Updated screenshots, rewrote network/encryption, cleaned up

 

1.9

 

10/17/2018

 

Added RSD pulse settings and registers

 

1.10

 

3/1/2019

 

Added section on digital outputs

 

1.11

 

4/9/20

 

Added Gateway Log support button, Digital Output Module

 

1.12

 

9/30/2020

 

Added Gateway log node statistics

 

1.13

 

3/15/21

 

Updated register map to include pulse output registers

 

1.14

 

8/4/2021

 

Updated register remap to 1500 registers

 

1.15

 

6/7/2022

 

Updated Modbus Gateway Register Map section

 

Содержание GWDIN


































Отзывы:

Нет отзывов