background image

 

C-DIAS PROCESSOR MODULE 

CCP 621 

 

27.03.2020 

Page 11 

X1:

 

USB Host 2.0

 

 

 

 
 

It should be noted that many of the USB devices on the market do not comply with 

USB specifications; this can lead to device malfunctions. It is also possible that 

these devices will not be detected at the USB port or function correctly. Therefore, it 

is recommended that every USB stick be tested before actual use. 

 

Il faut souligner que la plupart des périphériques USB sur le marché ne sont pas 

conformes aux spécifications USB, ce qui peut entraîner des dysfonctionnements de 

l'appareil. Il est également possible que ces dispositifs ne seront pas détectés par le 

port USB ou qu’ils ne fonctionnent pas correctement. Par conséquent, il est recom-

mandé que chaque clé USB soit testée avant l'utilisation sur l’automate. 

 

 
X2:

 

Ethernet

  

 

 

 

  n.c. = do not use

 

 
 
X3:

 

VARAN Out

 

 

 

 
 

More information on the VARAN bus can be found in the VARAN bus specifications!

 

 

Pin

 

Function 

+5 V 

D- 

D+ 

GND 

Pin

 

Function 

TX+ 

TX- 

RX+ 

4 - 5 

n.c. 

RX- 

7 - 8 

n.c. 

Pin

 

Function 

TX+ / RX+ 

2  

TX- / RX- 

RX+ / TX+ 

4 - 5 

n.c. 

RX- / TX- 

7 - 8 

n.c. 

Содержание CCP 621















































Отзывы: