SIGMATEK C-DIAS Скачать руководство пользователя страница 2

Страница: 2 / 22

C-DIAS ANALOG INPUT MODULE

CAI 042

Number of filters per channel

2 (1 fix, 2. 4-step settable)

Calibratable

Yes

Serial interface

Analysis with hyper terminal possible

So that the maximum load for the reference voltage is not exceeded, a maximum of 4

bridges with a minimum resistance of 300Ohms can be connected to the CAI 042.

Here, it doesn’t matter if 4 bridges are connected parallel with one channel or if each

channel is connected to a single bridge.

Afin de ne pas dépasser la charge maximale de la tension de référence, au maximum 4

ponts d’une résistance supérieure ou égale à 300 ohms peuvent être connectés à la

CAI 042. Il est sans importance si quatre ponts sont connectés en parallèle avec un canal

ou si chaque canal est connecté à un seul pont.

Step response of the analog and digital filters (20mV steps)

20000

40000

60000

80000

100000

Samples [n]

Filterausgang [dezimal]

Filter 2-1

Filter 2-2

Filter 2-3

Filter 2-4

Filter 1

Electrical Requirements

Supply from C-DIAS Bus

+5V and +24V

Current consumption of the
C-DIAS Bus (+5 V supply)

Typically 50mA

Maximum 70mA

Current consumption of the
C-DIAS Bus (+24 V-supply)

Typically 200mA

Maximum 250mA

Page 2

02.08.2011

Содержание C-DIAS























Результаты поиска

Содержание C-DIAS

Отзывы:

Похожие инструкции для C-DIAS

Бренды по названию

Популярные бренды

SIGMATEK C-DIAS, Технические данные инструкция

Результаты поиска

Содержание C-DIAS

Отзывы:

Похожие инструкции для C-DIAS

Бренды по названию

Популярные бренды