SIGMATEK C-DIAS Скачать руководство пользователя страница 1

Страница: 1 / 22

C-DIAS ANALOG INPUT MODULE

CAI 042

C-DIAS Analog Input Module

CAI 042

4 x resistance

measurement

bridges ±2mV / V

The calibratable CAI 042 DMS module is used to record data
from resistance measurement bridges

(e.g. load cells). With an

18-bit resolution, measurement values with an accuracy of
±0,01% are available.

Technical Data

Analog Channel Specifications

Number of channels

1,2 or 4

Load cells parameter

2mV / V

Measurement range

±20 mV

Measurement value

±105000 d

Resolution

Internal 24 bit

(From the 18 bit measurement value)

Conversion time for all channels

14ms / 4 Channel drive

8ms / 2 Channel drive

4ms / 1 Channel drive

Bridge supply voltage

10V

Maximum load of the voltage
supply (entire supply)

135mA

Maximum resistance per channel
(using all 4 channels)

300Ohm to 5000Ohm

Allowable resistance (parallel
circuit of all 4 bridges)

75Ohm to 5000Ohm

Analog channel measurement
accuracy

±0,01% of maximum measurement value

(With an operating temperature from 0 to +40°C)

02.08.2011 Page

Содержание C-DIAS























Результаты поиска

Содержание C-DIAS

Отзывы:

Похожие инструкции для C-DIAS

Бренды по названию

Популярные бренды

SIGMATEK C-DIAS, Технические данные инструкция

Результаты поиска

Содержание C-DIAS

Отзывы:

Похожие инструкции для C-DIAS

Бренды по названию

Популярные бренды