manualshive.com logo in svg

SIGMATEK 074.00660, Руководство по установке электроустановки


Поделиться
Скачать
background image

84

                                                                         Sigmatek FDD Sizes 7 to 9 Power Installation Guide

5.1.11     RoHS compliance

The drive meets EU directive 2011/65/EU for RoHS compliance.

5.1.12     Vibration

Maximum recommended continuous vibration level 0.14 g r.m.s. broad-band 5 to 200 Hz.

 

This is the limit for broad-band (random) vibration. Narrow-band vibration at this level which 
coincides with a structural resonance could result in premature failure.

Bump Test 

Testing in each of three mutually perpendicular axes in turn.
Referenced standard:IEC 60068-2-29: Test Eb:
Severity: 18 g, 6 ms, half sine
No. of Bumps: 600 (100 in each direction of each axis)

Random Vibration Test 

Testing in each of three mutually perpendicular axes in turn.
Referenced standard:IEC 60068-2-64: Test Fh:
Severity: 1.0 m²/s³ (0.01 g²/Hz) ASD from 5 to 20 Hz

   -3 dB/octave from 20 to 200 Hz

Duration: 30 minutes in each of 3 mutually perpendicular axes.

Sinusoidal Vibration Test 

Testing in each of three mutually perpendicular axes in turn.
Referenced standard: IEC 60068-2-6: Test Fc:
Frequency range: 5 to 500 Hz
Severity:       3.5 mm peak displacement from 5 to 9 Hz

        10 m/s² peak acceleration from 9 to 200 Hz
         15 m/s² peak acceleration from 200 to 500 Hz

Sweep rate:  1 octave/minute
Duration:       15 minutes in each of 3 mutually perpendicular axes.

EN 61800-5-1:2007, Section 5.2.6.4. referring to IEC 60068-2-6

Frequency range: 10 to 150 Hz
Amplitude:    10 to 57 Hz at 0.075 mm pk

         57 to 150 Hz at 1g p

Sweep rate:  1 octave/minute
Duration:       10 sweep cycles per axis in each of 3 mutually perpendicular axes

5.1.13     Starts per hour

By electronic control: unlimited
By interrupting the AC supply: 

20 (equally spaced)

5.1.14     Start up time

This is the time taken from the moment of applying power to the drive, to the drive being ready to run 
the motor:
Size 7 to 9: 5 s
For faster start up time a 24 V backup supply can be used, see section 4.4

24 Vdc supply

on page 62

5.1.15     Output frequency / speed range

FDD

 models:

In all operating modes (Open loop, RFC-A, RFC-S) the maximum output frequency is limited to 550 
Hz.

NOTE

Содержание 074.00660



































































































Отзывы:

Нет отзывов

Похожие инструкции для 074.00660

D-Link DES-7200 User Manual preview
DES-7200
Бренд: D-Link Страницы: 100
D-Link DES-3226L Manual preview
DES-3226L
Бренд: D-Link Страницы: 134
D-Link DES-3010F Command Line Interface Manual preview
DES-3010F
Бренд: D-Link Страницы: 187
D-Link DES-3010F Manual preview
DES-3010F
Бренд: D-Link Страницы: 225
D-Link DES-1048G Manual preview
DES-1048G
Бренд: D-Link Страницы: 31
D-Link DES-1050G User Manual preview
DES-1050G
Бренд: D-Link Страницы: 35
D-Link DES-1016D - Switch Quick Install Manual preview
DES-1016D - Switch
Бренд: D-Link Страницы: 19
D-Link COVR-2202 User Manual preview
COVR-2202
Бренд: D-Link Страницы: 107
D-Link AirPlusXtremeG DI-624 Troubleshooting preview
AirPlusXtremeG DI-624
Бренд: D-Link Страницы: 5
D-Link DGS-1210-28P Getting Started Manual preview
DGS-1210-28P
Бренд: D-Link Страницы: 48
A-Link WNAP4G Quick Installaion Manual preview
WNAP4G
Бренд: A-Link Страницы: 6
DataRemote CDS-9010 Quick Start Manual preview
CDS-9010
Бренд: DataRemote Страницы: 2
Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Бренд: Lattice Semiconductor Страницы: 15
Blackrock Microsystems Cerebus Instructions For Use Manual preview
Cerebus
Бренд: Blackrock Microsystems Страницы: 27
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Бренд: FS Страницы: 19
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Бренд: Zhone Страницы: 114
Avaya ERS 5510 Technical Configuration Manual preview
ERS 5510
Бренд: Avaya Страницы: 73
Aurora EGO AE120 User Manual preview
EGO AE120
Бренд: Aurora Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды