SIGMATEK 074.00660 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 98

background image

Sigmatek FDD Sizes 7 to 9 Power Installation Guide

11

Safety i

Pro
duc

M

Ele
ctri

Te

UL
li

Typical short term overload limits

The maximum percentage overload limit changes depending on the selected motor. Variations in
motor rated current, motor power factor and motor leakage inductance all result in changes in the
maximum possible overload. Typical values are shown in the table below:

Table 2-3 Typical overload limits

Generally the drive rated current is higher than the matching motor rated current allowing a higher
level of overload than the default setting.
The time allowed in the overload region is proportionally reduced at very low output frequency on
some drive ratings.

Output current

The continuous output current ratings given on the rating label are for maximum 40



C (104



F),

1000 m altitude and 3 kHz switching frequency (except where shown). Derating is required for higher
switching frequencies, ambient temperatures >40



C (104



F) and higher altitude. For derating

information, refer to

Chapter 5 Technical data

Input current

The input current is affected by the supply voltage and impedance. The input current given on the
rating label is the typical input current and is stated for a balanced supply.

Operating mode

RFC from cold RFC from 100 %

Open loop

from cold

Open loop

from 100 %

Normal Duty overload with motor rated
current = Maximum drive normal duty
rated current

110 % for 165 s

110 % for 9 s

110 % for 165 s

110 % for 9 s

Heavy Duty overload with motor rated
current = Maximum drive Heavy duty rated
current (size 8 and below)

200 % for 28 s

200 % for 3 s

150 % for 60 s

150 % for 7 s

Heavy Duty overload with motor rated
current = Maximum drive Heavy duty rated
current (size 9 and 10)

175 % for 42 s

175 % for 5 s

136 % for 81 s

136 % for 11 s

The maximum overload level which can be attained is independent of the speed.

NOTE

«
...
9
10
11
12
13
...
»

Содержание 074.00660



































































































Отзывы:

Нет отзывов

Похожие инструкции для 074.00660

NetDefend DFL-260E

Бренд: D-Link Страницы: 328

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

DFL-210 - NetDefend - Security Appliance

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 4

Бренд: Dahua Страницы: 12

NetDefend DFL-1600

Бренд: D-Link Страницы: 23

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

Бренд: NavigateWorx Страницы: 71

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Бренд: Delta Страницы: 2

Бренд: U.S. Products Страницы: 80

Бренд: peplink Страницы: 2

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды