Sigma FOS-01 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 17

background image

5.x Installation and Environmental Considerations

FOS-01 Operation Manual

Page 11 of 17

5.4 Multiple Switches connected in series

Fiber Optic Switches can be connected in series as shown above. This however leads to additional optical
losses occurring in the system due to multiple switches. Each Fiber Optic Switch adds <4dB (typical 3dB) loss.
When using the switches with a Fiber Optic Interface, refer to FOI Operation Manual (ANNEX A) for a detailed
optical power margin calculation and the maximum number of switches that can be connected in series.

Fiber Optic Cable

62.5/125µm, MM

Fiber Optic Switches

FOS-01-xxx

Fiber Optic Interface

FOI-01-221

«
...
9
10
11
12
13
...
»

Содержание FOS-01


















Отзывы:

Нет отзывов

Похожие инструкции для FOS-01

Бренд: AbleNet Страницы: 2

SmartCell 6A000

Бренд: Cabletron Systems Страницы: 114

Бренд: Cabletron Systems Страницы: 62

CyberSWITCH CSX150

Бренд: Cabletron Systems Страницы: 49

Cabletron CyberSWITCH CSX5500

Бренд: Cabletron Systems Страницы: 729

Бренд: CAME Страницы: 2

Бренд: IDEC Страницы: 8

Бренд: IDEM SAFETY SWITCHES Страницы: 2

Бренд: LAUMAS Страницы: 40

Бренд: Little Giant Страницы: 2

IES8242MPp9H-S-DR

Бренд: OTS Страницы: 3

Бренд: Accton Technology Страницы: 7

Бренд: DeLOCK Страницы: 26

Бренд: 3Com Страницы: 62

Бренд: National Instruments Страницы: 23

Бренд: ATEN Страницы: 9

Бренд: Pakedge Device & Software Страницы: 8

Бренд: Black Box Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды