SIG KADET EP-42B Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 16

SIG KADET EP-42B Скачать руководство пользователя страница 15

15

WARNING! THIS IS NOT A TOY!

Flying machines of any form, either model-size or full-size, are not toys!
Because of the speeds that airplanes must achieve in order to fly, they are
capable of causing serious bodily harm and property damage if they crash.

IT IS YOUR RESPONSIBILITY AND YOURS ALONE

to assemble this

model airplane correctly according to the plans and instructions, to ground
test  the  finished  model  before  each  flight  to  make  sure  it  is  completely
airworthy,  and  to  always  fly  your  model  in  a  safe  location  and  in  a  safe
manner.  The first test flights should only be made by an experienced R/C
flyer, familiar with high performance R/C aircraft.

JOIN THE AMA

The governing body for radio-control model airplanes in the United States
is the ACADEMY OF MODEL AERONAUTICS, commonly called the AMA.
The AMA SAFETY CODE provides guidelines for the safe operation of R/C
model airplanes.  While AMA membership is not necessarily mandatory, it
is  required  by  most  R/C  flying  clubs  in  the  U.S.  and  provides  you  with
important  liability  insurance  in  case  your  R/C  model  should  ever  cause
serious property damage or personal injury to someone else.

ACADEMY OF MODEL AERONAUTICS

5161 East Memorial Drive

Muncie, IN 47302

Telephone: (765) 287-1256

AMA WEB SITE: www.modelaircraft.org

CUSTOMER SERVICE

SIG  MFG.  CO.,  INC.  is  committed  to  your  success  in  both  assembling
and flying the KADET EP-42B ARF.  Should you encounter any problem
building this kit or discover any missing or damaged parts, please feel free
to contact us by mail or telephone.

SIG MFG. CO., INC.

P.O. Box 520

401 South Front Street

Montezuma, IA 50171-0520

PHONE: 1-641-623-5154

FAX: 1-641-623-3922

SIG WEB SITE: www.sigmfg.com

SIG E-MAIL: [email protected]

LIMIT OF LIABILITY

The  craftsmanship,  attention  to  detail  and  actions  of  the  builder/flyer  of
this  model  airplane  kit  will  ultimately  determine  the  airworthiness,  flight
performance, and safety of the finished model.  SIG MFG. CO.’s obligation
shall be to replace those parts of the kit proven to be defective or missing.
The  user  shall  determine  the  suitability  of  the  product  for  his  or  her
intended use and shall assume all risk and liability in connection therewith.

KADET EP-42B LOG BOOK

Date:

Battery Pack:

Propeller:

Comments:

«
...
13
14
15
16
»

Содержание KADET EP-42B

















Отзывы:

Нет отзывов