SIG Extra 300XS Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 26

SIG Extra 300XS Скачать руководство пользователя страница 26

26

For the SIG EXTRA 300XS - we recommend the

FPE 2.4 cu.in. Gas Engine

This is no overweight, bone-jarring converted lawn care engine!

Chock full of power, the FPE 2.4 is the lightest, smoothest running
engine in its class. Utilizing a premium Husqvarna piston and
cylinder,

First Place Engines

machines all other major components

from billet aluminum and bar steel stock. It’s a gas engine
designed and produced by modelers for modelers. The perfect
power plant for the SIG Extra 300XS!

Specifications:
Size:

2.4 cubic inches (40 cc)

Weight:

52 ounces with muffler

Prop:

20x10

RPM:

7,400 rpm (APC 20x10)

Thrust:

20 pounds

Horsepower:

1.7

Item #FPE24

PROUDLY MADE IN THE U.S.A.

Dedicated to providing the most power at a reasonable cost, First Place Engines are your

best choice for large, gasoline powered model airplane power plants. All engines use piston
and cylinder assemblies from world-renowned manufacturers such as Husqvarna and
Sachs/Makita, insuring long life and easy operation. Using state-of-the-art CNC machines,
First Place produces all other major components from high quality billet aluminum and/or
bar steel stock. All engines are internally balanced using needle bearings at the top and
bottom of the connecting rod, giving you smooth operation. Each First Place Engine comes
complete with an electronic ignition system, smoke-ready TIG welded custom aluminum
muffler, complete instructions, and a one-year limited warranty.

Sig Manufacturing is pleased to be the exclusive distributor of First Place Engines.

WANT A GAS ENGINE FOR YOUR

EXTRA 300XS ARF? CHECK THIS OUT!

«
...
24
25
26

Содержание Extra 300XS



























Отзывы:

Нет отзывов