Sierra Titanium Power TM1200.1D, Руководство пользователя

Страница: 10 / 19

FEATURE OVERVIEW
●
2 Ohm Stable MOSFET Amplifier Design
●
Intercooled Semi-conductor Technology
●
Accurate Stated Amplifier Ratings
●
Gold/Silver Plated 4 Gauge Powwer and Ground Connections
●
Variable Bass Boost 0 - +18dB at 45Hz
●
Gold/Silver Plated Audio Input and Output Connections
●
Varable LP and HP Electronic X-OVER @ 12dB/octave
●
Gold/Silver Plated RCA Output for multi-amp Installations
●
Varable Subsonic Filter from 20Hz - 55Hz @ 12dB/octave
●
Bass Remote Controller available (not included)
●
Regulted Amplifier Technology
(1)
RCA OUTPUT
(4)
BASS BOOST
Use these RCA output connectors to connect to a secondary This a variable control to increase the bass boost at 45Hz from
amplifier. This output PASS-THRU connection derived from the 0 - +18dB of gain, adjust to suit.
RCA input connector so the signal level and frequency response
is the same as the original input signal.
(5)HIGH PASS
RCA INPUT Set the crossover switch to HP and turn this control to 65Hz
Connect these RCA connectors to a head unit with a LOW LEVEL or above when using speaker's smaller than 6 x 9", this feature
Output connection. is designed to filter out all low bass frequencies that only
SUBWOOFERS should produce. NOTE : Failure to do so could
(2)
LEVEL
result in speaker damage.
This allows level adjustment of the input signal. Use this control
to correctly match the amplifier. To set this control correctly,
(6)LOW PASS
turn the amplifier level to MIN and the head unit to 3/4 volume, Set the crossover switch to LP when a subwoofer is connected.
with the BASS and TREBLE on zero, then slowly turn up this Ensure the crossover frequency is set at 100Hz or below, this
amplifier level control towards towards the MAX end of the feature is designed to filter out all mid to high frequencies that
control. NOTE : If the sound becomes distorted, turn this only FULL RANGE speakers should produce. NOTE : Failure to do
control down. so could result in speaker damage.
(3)
SUBSONIC FILTER
(7)
CROSSOVER SELECTOR
This is a variable control that filters out all Sub Bass Frequencies Set the apprpriate mode of operation. The 3 positions available
point at 12dB/octave. are OFF, LP and HP.
(8)
POWER, STATUS AND THERMAL LED's
at the battery end. NOTE : This is to be last wire to connect up
This shows if the amplifier has been correctly powered up and if during installation as damage could result.
any faults are present.
(9)BASS REMOTE CONNECTOR
(13)
REMOTE INPUT
This port allows connection th the (optional) bass control. This terminal is for turning the amplifier on and off. This requires a
switched postive (+)12V to power 'ON' the amplifier, this can be
(10)BASS REMOTE SWITCH found on the rear of the head unit in the form of a electric
Use the switch to activate or de-activate the (optional) bass controller. antenna output, or a remote on output. If not available you can
wire to the ACC position on the key.
(11)GROUND INPUT
Connect directly to the vehicle's chassis via a 4 gauge power cable.
(14)
FUSES
NOTE : This is to be the first wire to connect when wiring up a amplifiers
Please ensure correct type of fuse is fitted.
damage could result if this not done.
(15)SPEAKER OUTPUT
(12)
+12V INPUT
See 2/1 channel installation diagrams in this manual for correct
This must be connected to the vehicle battery po) terminal speaker connection.
via a 4 gauge power cable and with an inline fuse or circuit breaker
FEATURE OVERVIEW
2 Channel Power Amplifier
TM300.2