Sierra Wireless WISMO Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 76

Sierra Wireless WISMO Series Скачать руководство пользователя страница 33

WA_DEV_W218_UGD_004

Page 33 of 75

WISMO Series Development Kit User

LED Signalization (D100, D101)

The LED signalization locations are shown in the following figure.

Figure 16. LEDs Location (D100, D101)

LED “UART1” (D100)

This green LED indicates the power supply state of UART1.
The interface can be used when it is lit, depending on which power supply is present (J600 or J604.
Refer to the section discussing Power Supplies for more information).

LED “RING INDICATOR” (D101)

The “RING INDICATOR” indicator is a yellow LED controlled by the RI signal on the WISMO218 or
the WISMO228.
When the WISMO218 or the WISMO228 receives an incoming call, the RI signal goes from high to low
for 0.5sec alternately, hence making the D101 LED blink

Enabling the UART1 Function (SW101)

The UART1 interface can be enabled by switching SW101 to the “ON” position. Please refer to the
following figure.

D101

D100

«
...
31
32
33
34
35
...
»

Содержание WISMO Series













































































Отзывы:

Нет отзывов