Sierra Wireless WISMO Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 76

Sierra Wireless WISMO Series Скачать руководство пользователя страница 12

WA_DEV_W218_UGD_004

Page 12 of 75

WISMO Series Development Kit User

(*) These signals from the connector side can be electrically disconnected from the WISMO218 or the
WISMO228 if the related jumper pads are dissociated. (Refer to the section discussing Special
Soldering for Jumper Pads for more information.)

Special Soldering for Jumper Pads

PCB jumper prints are used for the electrical removal of peripherals from the WISMO218 or the
WISMO228.
To connect signals between the WISMO218 or the WISMO228 (from J1000 and J1001) and the
dedicated connectors on the WISMO Series Development Kit board, solder these PCB jumper prints.
To connect signals between the WISMO Series Socket-Up Board and the external board connector
(J1100), it is recommended NOT to solder the PCB prints. Then, a daughter board can be prototyped
to connect the WISMO Series Socket-Up Board directly through the board connector (J1100).

Figure 2. Jumper Solder Pad

The interfaces (or signals) listed below could be electrically removed by dissociating the following
PCB jumper prints:

•

UART1 (from J101 to J108)

•

UART-SPI (UART2 connector, from J201 to J204)

•

AUDIO2 (from J702 to J705)

•

SIM (from J401 to J405)

•

Power supply of the WISMO Series Development Kit interfaces (all components from J605,
except the WISMO218 or the WISMO228. For more information, see § 7 Current Consumption
Measurement).

•

BUZZ-OUT signal (with J603)

•

FLASH-LED signal (with J602)

RoHS Compliance

The WISMO Series Development Kit board is compliant with RoHS (Restriction of Hazardous
Substances in Electrical and Electronic Equipment) Directive 2002/95/EC which sets limits for the use
of certain restricted hazardous substances. This directive states that “from 1st July 2006, new electrical
and electronic equipment put on the market does not contain lead, mercury, cadmium, hexavalent
chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE)”.

Both the WISMO218 and the WISMO228 are compliant with this directive
and are identified by the RoHS logo on their labels.

«
...
10
11
12
13
14
...
»

Содержание WISMO Series













































































Отзывы:

Нет отзывов