Sierra Wireless Raven iDEN Скачать руководство пользователя страница 31

Страница: 31 / 159

Raven iDEN

20070914

Figure 3-11: HyperTerminal : connected

Tip: You will not be prompted for a password if you connect using a
COM port.

Type

and

press

Enter

You

should

get

“OK”

“0”.

see

what

you

are

typing

you

type

it,

you

will

need

turn

the

echo

and

verbose

mode.

Type

ATE1V1

and

press

Enter

you

get

“OK”,

then

you

entered

the

command

successfully.

you

get

“0”

“ERROR”,

try

entering

the

command

again.

5. Enter the Master Reset Command for
iDEN

Type

AT*PROVISION=000000,

0123456789

The

Raven

should

respond

with:

“Master

Reset

Succeeded”.

With

any

other

response,

contact

TELUS

check

the

account

status.

Press

the

reset

button

the

Raven.

The

Raven

should

now

the

network.

Содержание Raven iDEN
































































































































































Результаты поиска

Содержание Raven iDEN

Отзывы:

Sierra Wireless Raven iDEN, Руководство пользователя, Страница: 31 / 159

Результаты поиска

Содержание Raven iDEN

Отзывы: