Sierra Wireless AirPrime WP7504 Скачать руководство пользователя страница 23

Regulatory Compliance and Industry Certifications

Rev 1  Apr.16

23

Specifications subject to change

·

The radiated power of a collocated transmitter must not exceed the EIRP 
limit stipulated in 

Table 5-2

.

5.

A label must be affixed to the outside of the end product into which the 
AirPrime WP7504 module is incorporated, with a statement similar to the 
following:

· This device contains FCC ID: N7NWP7 / IC:2417C-WP7.

6.

A user manual with the end product must clearly indicate the operating 
requirements and conditions that must be observed to ensure compliance 
with current FCC / IC RF exposure guidelines.

The end product with an embedded AirPrime WP7504 module may also need to 
pass the FCC Part 15 unintentional emission testing requirements and be 
properly authorized per FCC Part 15.

Note:  If this module is intended for use in a portable device, you are responsible for 
separate approval to satisfy the SAR requirements of FCC Part 2.1093 and IC RSS-102.

Table 5-2:  Collocated Radio Transmitter Specifications 

Device

Technology

Frequency

(MHz)

EIRP Limit

(dBm)

Collocated 
transmitters

1

1. Valid collocated transmitter combinations: WLAN+BT; WiMAX+BT.

(WLAN+WiMAX+BT is not permitted.)

WLAN

2400–2500

25

5150–5850

27

WiMAX

2300–2400

25

2500–2700

25

3300–3800

25

BT

2400–2500

15

Содержание AirPrime WP7504

























Отзывы: