8
Installation
– Scope of delivery: dryer, installation and instruction manual, basket for woollens
(depending on the model).
– Check dryer for transport damage.
– The dryer is very heavy. Do not lift without assistance.
– Be careful to avoid sharp edges.
– Do not install in a room which is susceptible to frost. Water may cause damage once it
starts to freeze.
– If in doubt, have the appliance connected by a specialist.
– Do not lift the dryer by any of the protruding parts (e.g. the door) as they may break off.
Setting up the dryer
– The appliance plug must always be accessible.
– Ensure that the appliance is installed on a clean,
level and firm surface.
– Do not obstruct the air inlet on the front of the
dryer.
– Keep the area around the dryer clean.
– Level the dryer using the threaded feet.
Use a spirit level.
– Do not remove the threaded feet under any
circumstances.
Mains connection
see safety information
a
Page 13.
– Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (
a
Page 10
) must be the
same.
– The connected load and necessary fuse protection are specified on the rating plate.
Frost protection
Preparation
1. Empty the condensate container
a
page 4
.
2. Select any programme using the programme selector.
3. Press the
Start
/Pause button
a
condensation is pumped into the container.
4. Wait 5 minutes and then empty the condensate container again.
5. Turn the programme selector to
Off
.
Transport
– Preparation of dryer
a
see Frost protection.
– Transport the dryer in a vertical upright position.
– Following transportation, leave the dryer to stand for two hours.
There may be residual water in the dryer.
This can leak out if the dryer is at an angle.
1.
Remove all accessories
from the drum.
The drum must be empty.
Make sure that the air inlet
remains unobstructed
Clean and level
Do not install the dryer behind a door or sliding
door, which could prevent or restrict opening of the
dryer door. This will prevent children from locking
themselves in and putting their lives in danger.
2.
Do not operate the dryer if
there is a danger of frost.
9
Only when the appliance is
switched off.
Care and cleaning
Heat exchanger
The heat exchanger of the dryer is cleaned automatically when drying is in progress,
Cln
appears in the display panel. Do not pull the condensate container out during the cleaning
process.
Dryer housing, control panel, air intake
Wipe with a soft, damp cloth.
Do not use harsh cleaning agents or solvents.
Remove detergent and cleaning agent residue immediately.
Some water may collect between the window and the seal during drying. This does not affect
the proper operation of your dryer in any way.
Filter in the condensate container
The filter is cleaned automatically when the condensate container is emptied.
However, the filter should still be cleaned regularly under running water. This prevents
stubborn deposits/dirt from building up.
Cleaning is only required if the symbol
ā
Container
flashes again in the display panel after
the condensate container has been emptied.
1.
Pull out the condensate container.
2.
Pull the filter out of its snap-in lock.
3.
Clean the filter under running water or in the dishwasher.
4.
Refit the filter.
5.
Insert the condensate container so that it locks into place.
Only operate the dryer with the filter inserted.
Moisture sensor
The dryer is equipped with stainless-steel moisture sensors. These measure how damp
the laundry is. After long periods of use, a fine layer of limescale can form on the moisture
sensors.
1.
Open the door.
2.
Clean the moisture sensors using a damp sponge with a rough surface.
Do not use steel wool or other abrasive materials.
10
Technical Data
ʠ
Dimensions (DxWxH)
60 x 60 x 85 cm (height adjustable)
Weight
approx. 53 kg
Max. capacity
7 kg
Condensate container
4.0 l
Connection voltage
220-240 V
Connected load
max. 800 W
Fuse protection
10 A
Ambient temperature
5 - 35°C
Product number Production number
Inside of door
The rating plate can be found on the back of the dryer.
Power consumption when switched off
0.10 W
Power consumption when ready for use (left-on mode)
1.00 W
ʠ
Drum interior light
(depending on model)
: The drum lights up after the door is opened and after the
programme starts, and switches off automatically.
Consumption values table
Programme
Spin speed which
is used for spinning
the laundry
Duration**
Energy consumption**
Ê
Cottons
7 kg
3.5 kg
7 kg
3.5 kg
·
Cupboard Dry*
1400 rpm
151 min
93 min
1.33 kWh
0.80 kWh
1000 rpm
178 min
110 min
1.65 kWh
0.97 kWh
800 rpm
205 min
127 min
1.92 kWh
1.13 kWh
Ô
Iron Dry*
1400 rpm
110 min
71 min
0.94 kWh
0.61 kWh
1000 rpm
137 min
88 min
1.24 kWh
0.80 kWh
800 rpm
166 min
111 min
1.55 kWh
1.04 kWh
Ï
Easy-Care
3.5 kg
3.5 kg
·
Cupboard Dry*
800 rpm
64 min
0.54 kWh
600 rpm
78 min
0.68 kWh
*
Programme setting for testing in accordance with the applicable EN61121 standard.
**
The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual moisture in the fabric
and the amount of laundry being loaded.
Most efficient programme for cotton fabrics
The following "standard cottons programme" (identified with
) is suitable for drying normal, wet cotton laundry and is most efficient in terms of
its combined energy consumption for drying wet cotton laundry.
Standard programme for cottons in accordance with current EU regulation 932/2012
Programme
Load
Energy consumption
Programme duration
Cottons Cupboard Dry
7 kg/3.5 kg
1.65 kWh/0.97 kWh
178 min/110 min
Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
Optional accessories
(order from the after-sales service using the order number, depending on the model)
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth to save space. The dryer
must be
fastened
to the washing machine using this connection set. WZ 20400: with pull-out worktop
.
Installation underneath the worktop
Instead of the appliance covering plate, you
must
have a metal cover fitted by a specialist.
Platform
For easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.
Wollens basket
For drying
individual
wollen fabrics, sports shoes and soft toys (see separate instructions for “Woollens basket”).
WZ
11410
WZ
20290
WZ
20500
WZ
20600
11
Normal noises
During drying, the compressor and the pump generate some noise which is entirely normal.
The compressor in the dryer may
occasionally generate a droning noise.
The volume and pitch of this may vary
depending on the selected
programmes and the progress of the
drying.
The compressor in the dryer is ventilated
from time to time, which creates a whirring
sound.
The automatic cleaning process causes
a clicking noise.
The process of pumping the condensation
into the condensate container generates
pumping noises.
12
What to do if ...
If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales service.
We will always find an appropriate solution and will avoid unnecessary visits by engineers. Trust
the expertise of the manufacturer and rest assured that the repair will be carried out by trained
service technicians using original spare parts. The contact details of your local after-sales service
can be found in the enclosed
after-sales service
directory.
When contacting the after-sales service, please quote the appliance's product number (E no.) and
production number (FD) (see the inside of the door).
Set the programme selector to
Off
and remove the appliance plug from the socket.
ʠ
The
Start
/Pause
indicator lamp does not
light up.
Mains plug plugged in?
Programme selected?
Check the socket fuse.
ʠ
The display panel light and
indicator lights
(depending
on model)
go out and the
Start
/Pause indicator
light flashes.
Energy-saving mode is activated
a
see the separate
Energy-saving mode
instructions.
ʠ
The
ā
Container
symbol
and
Start
/Pause
indicator lamp flash.
Empty container for condensation
a
see page 4
.
Clean the condensate container filter if necessary
a
Page 9
.
Each time the dryer is transported, you must wait two hours before
operating it.
ʠ
The
4
Fluff filter
symbol
and
Start
/Pause
indicator lamp flash.
Rinse the fluff filter under running water
a
Page 4.
ʠ
Dryer does not start.
Start
/Pause button selected?
Door closed?
Programme set?
Ambient temperature greater than 5°C?
ʠ
Water is leaking out.
Make sure the dryer is level.
ʠ
The door opens by itself.
Push the door closed until you hear it click into place.
ʠ
Creasing.
Laundry load exceeded?
Remove articles of clothing immediately after the end of the
programme, hang up and pull into shape.
Unsuitable programme selected
a
Page 7.
ʠ
Laundry is not dried
correctly or is still too
damp.
After the end of the programme, warm laundry feels damper than it
actually is. Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but
does not increase the temperature. Your laundry will become drier.
Select a programme with a longer drying time or increase the drying
level. This does not increase the temperature.
Select a timed programme for subsequent drying of laundry that is
still damp.
If you have exceeded the maximum load for the programme, the
laundry may not be dried properly.
Clean the moisture sensor in the drum. A fine layer of limescale may
adversely affect the performance of the sensors and your washing
will not dry properly.
Drying has been interrupted as a result of a power cut, because the
condensation container is full or because the maximum drying time
has been exceeded.
ʠ
Drying time too long.
Rinse the fluff filters under running water
a
Page 4.
Insufficient supply of air
a
ensure that air can circulate.
Air inlet possibly blocked
a
Clear inlet
a
Page 8
.
Ambient temperature higher than 35°C
a
ventilate the room.
ʠ
The humidity in the room
increases significantly.
Make sure the room is sufficiently ventilated.
ʠ
Cln
appears in the display
panel.
Not an error! Automatic cleaning of the heat exchanger.
Do not empty the condensate container.
ʠ
Power failure.
Remove the laundry from the dryer immediately and spread it out.
Heat may escape. Be careful as the door, the drum and the laundry
may be hot.
ʠ
Other intermittent noises
and vibrations.
Not an error!
Normal noises
a
Page 11
.
13
Safety instructions
Emergency
– Pull the appliance plug out of the socket immediately or disconnect the fuse.
ONLY use the
dryer...
– in rooms inside the house.
– to dry fabrics.
The dryer
must
NEVER...
– be used for purposes other than those described above.
– be modified in terms of its technology or properties.
Hazards
– The dryer must not be used by children or persons who have not been
instructed in its use.
– Do not leave children unsupervised near the dryer.
– Keep pets away from the dryer.
– Remove all objects from the pockets of garments.
Pay particular attention to cigarette lighters
a
Risk of explosion!
– Do not lean or sit on the door
a
Risk of tipping!
Installation
– Secure loose cables
a
Tripping hazard!
– Do not operate the dryer where there is a risk of frost.
Mains
connection
– Connect the dryer according to specifications to an AC earthed socket,
otherwise it cannot be guaranteed that the appliance is completely safe.
– The cable cross-section must be sufficient.
– Only use earth-leakage circuit breakers with the following symbol:
– The appliance plug and socket must be compatible.
– Do not use multiple plugs/connectors and/or extension cables.
– Do not touch or hold the appliance plug with wet hands
a
Risk of electric
shock!
– Never pull the appliance plug out of the socket by its cable.
– Do not damage the mains lead
a
Risk of electric shock!
Operation
– Only laundry must be loaded into the drum.
Before switching on the dryer - check the contents.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax,
grease or paint (e.g. hair setting spray, nail polish remover, stain remover,
cleaning solvent, etc.)
a
Fire/explosion hazard!
– The tumble dryer is not to be used if industrial chemicals have been used for
cleaning.
– Hazard caused by dust (e.g. coal dust, flour): do not use the dryer
a
Risk of explosion!
– Do not turn off the dryer until the drying process ends, unless the laundry will
be removed quickly and spread out, so that the heat can dissipate.
– Do not put laundry containing foamed material/rubber in the dryer
a
elastic
material may be destroyed and the dryer may be damaged due to possible
deformation of the foamed material.
– Light things, such as long hair, may be sucked into the air inlet of the dryer
a
Risk of injury!
– Final part of a tumble dryer cycle occurs without heat (cool down cycle), to
ensure that the items are left at a temperature that ensures that the items will
not be damaged.
– Switch off the dryer once the programme has ended.
– The water from condensation is not drinking water and may be contaminated
with fluff.
Defect
– Do not use the dryer if it is defective or if you suspect that it is.
Repairs must only be carried out by the after-sales service.
– Do not use a dryer with a faulty mains lead. To prevent risks, a faulty mains lead
must only be replaced by the after-sales service.
Spare parts
– Only use genuine spare parts and accessories for safety reasons.
Disposal
– Dryer: unplug the appliance plug,
then
cut the mains lead from the appliance.
Dispose of the dryer at an approved public disposal facility.
– The dryer's heat exchanger contains fluorinated greenhouse gas R134a in a
hermetically sealed unit
a
dispose of in a proper manner. Capacity: 0.22 kg.
– Packaging: keep all packaging out of reach of babies and children.
a
Danger of suffocation!
– All materials are environmentally safe and recyclable.
Dispose of in an environmentally-responsible manner.
siemens-home.com/welcome
Register
your
product
online
Dryer
WT46W564BY
en
Dryer
Operating and installation instructions
Observe the safety instructions on page 13.
Read these instructions and the separate
Energy-saving mode
instructions before
switching on the dryer.
