a
Ê
:
Ĉ
ć÷
Ôü
h
o
Ï
:
Ĉ
ć÷
Ô
h
o
Í
:
Ĉ
ć÷
Ô
h
ü
:
Ĉ
ć÷
Ô
h
g
:
Ĉ
ć÷
Ô
h
Ô
5
:
Ĉ
ć÷
Ôü
h
dü
É
:
ä
6c
:
¼
:
Ĉ
ć÷
Ô
h
:
Ĉ
ć÷
h
mü
lü
Ĉ
Í
ü
Ê
Ê
Ê
Ê
Ï
c
Í
5
dü É
Ê
ć
Ï
a
a
a
a
l
lü
11
What to do if ...
ʑ
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
–
Start
/Reload not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
a
page
10
.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Programme stopped?
a
page 4
.
–
c
(without final spin) selected?
a
page 3, 4.
– Can be opened by emergency release only?
a
page 9.
ʑ
Programme does not start. –
Start/
Reload or
(Finished in)
time selected?
– Washing machine door closed?
– Childproof lock active? Deactivate
a
page
5
.
ʑ
Detergent solution is not
drained.
–
c
(without final spin) selected?
a
page 3, 4.
– Clean the detergent solution pump
a
page
10
.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Unsatisfactory spin result.
Laundry wet/too damp.
– Not a fault - the unbalanced-load detection system has cancelled
the spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum.
–
Ô
(Easy-Iron)
selected?
a
page 5.
– Selected speed too low?
a
page 5
.
ʑ
The programme duration
changes during the wash
cycle.
– Not a fault – the programme sequence is optimised for the
particular wash process. This may result in changes to the
programme duration in the display field.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
a
page
9
.
ʑ
Odour formation in the
washing machine.
– Run programme
Ê
Cottons 90 °C
without laundry. Use standard
detergent.
ʑ
Status display
³
tü
(Wash)
flashes.
Foam may be coming out
of the detergent drawer.
– Too much detergent used? Mix 1 tablespoon of fabric softener
with ½ lit,re of water and pour into dispenser
II
(not for outdoor
and down-filled textiles!).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and “wandering”
during the spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet
a
Installation instructions
.
– Transportation safety devices removed?
Remove the transportation safety devices
a
Installation
instructions
.
ʑ
Noises during spin and
drain cycles.
– Clean detergent-solution pump
a
page 10.
ʑ
Display panel/indicator
lamps do not function
during operation.
– Power cut?
– Fuses triggered? Reset/change the fuse.
– If the fault occurs repeatedly, call customer services.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced load detection system adjusts imbalance
by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
ʑ
Detergent residues on the
laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Use the
mü
Rinse
cycle or brush out the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to
Off
and remove the mains plug from the socket.
– Turn off the water supply and call customer services
a
Installation instructions.
siemens-home.com/welcome
Register
your
product
online
Washing machine
WM14E469BY
en
Washing machine
operating instructions
Observe the safety instructions on page 8.
Read these instructions and the separate installation
instructions before operating the washing machine.
