Siemens WM12W440IN Скачать руководство пользователя страница 32

Страница: 32 / 48

Faults and what to do about them.

Faults and what to do about them.

Faults

Cause/Remedy

Water is leaking from the

machine.

■

Attach the drain hose correctly or replace it.

■

Tighten the screw fitting on the supply hose.

The machine is not filling

with water.
Detergent is not being

dispensed.

■

Have you pressed the

button?

■

Is the tap turned on?

■

Could the filter be clogged? Clean the filter.

Page 29

■

Is the supply hose kinked or trapped?

The door cannot be

opened.

■

The safety function is activated. Stop the programme?

Page 23

■

selected (Rinse Stop = no final spin)?

Page 23

■

Can the door only be opened by the emergency release?

Page 30

The programme will not

start.

■

Have you pressed the

button or selected

Finish in

time?

■

Is the door closed?

■

Is the

childproof lock activated? Deactivate it.

Page 22

The drum briefly jerks or

judders after the

programme has started.

Not a fault – the internal motor test may cause the drum to jerk or judder briefly

when the wash programme starts.

The water is not draining.

■

selected (Rinse Stop = no final spin)?

Page 23

■

Clean the drain pump.

Page 28

■

Clean the drain pipe and/or the drain hose.

Water is not visible in the

drum.

Not a fault – the water is below the visible area.

The spin result is not

satisfactory.
Laundry is wet/too damp.

■

Not a fault – the unbalanced load detection system has interrupted the spin

cycle because the laundry is unevenly distributed.

Distribute small and large items of laundry evenly in the drum.

■

Easy Iron

selected (depending on the model)?

Page 19

■

Is the selected speed too low?

The spin cycle runs

several times.

Not a fault – the unbalanced load detection system is adjusting an imbalance.

The programme is taking

longer than usual.

■

Not a fault – the unbalanced load detection system is adjusting an

imbalance by repeatedly distributing the laundry.

■

Not a fault – the foam detection system is active – a rinse cycle has been

switched on.

Page 22

The length of the

programme changes

during the wash cycle.

Not a fault – the programme sequence is optimised for the specific washing

process. This may change the length of the programme shown in the display

panel.

Residual water in the

care-product

compartment

■

Not a fault – the effect of the care product is not affected.

■

Clean the insert if necessary.

Page 28

Содержание WM12W440IN

















































Результаты поиска

Содержание WM12W440IN

Отзывы:

Похожие инструкции для WM12W440IN

Бренды по названию

Популярные бренды

Siemens WM12W440IN, Инструкция по эксплуатации и руководство по установке

Результаты поиска

Содержание WM12W440IN

Отзывы:

Похожие инструкции для WM12W440IN

Бренды по названию

Популярные бренды