a
i
Êü
¥Ê
i
â
¢
o
ª
ü
¥Ê
i
â
¢
Ï
¥Ê
i
â
¢
o
Íü
¥Ê
i
â
¢
f
¥Ê
i
â
¢
g
¥Ê
i
â
¢
â
5
¥Ê
i
â
¢
:
É
¥Ê
¼
¥Ê
i
â
¢
?
¥Ê
m
l
Êü
@
Êü
@
Êü
@
Êü
@
Ïü
B
Íü
5ü
B
ÿü
Éü
B
Ï
i
Ê
~
a
ʑ
ʑ
ʑ
a
l
c
l
11
What to do if...
ʑ
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
–
Start/
Pause
not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
a
page 10.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Programme stopped?
a
page 4
.
– - - - - (Rinse stop = no final spin) selected?
a
page 3,4.
ʑ
Programme does not start. –
Start
/Pause
or
(Finished in)
time selected?
– Washing machine door closed?
– Childproof lock active? Deactivating
a
page 5.
ʑ
Detergent solution is not
drained.
– - - - - (Rinse stop = no final spin) selected?
a
page 3, 4.
– Clean the detergent solution pump
a
page 10.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Spin result not satisfactory.
Laundry wet/too damp.
– Not a fault - the imbalance monitoring system has interrupted the spin
because the laundry is unevenly distributed.
Distribute large and small items of laundry evenly in the drum.
–
â
Easy Iron
selected?
a
Page 5
– Speed selected too low?
a
page 5
.
ʑ
The programme duration
changes during the wash
cycle.
– Not a fault - the programme cycle is optimised for the particular
washing process. This can cause changes in the programme duration
on the display panel.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced-load detection system is adjusting the
imbalance.
ʑ
Residual water in the
0
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
a
page 10
.
ʑ
Odour formation in the
washing machine.
– Run programme
Ê
Cottons 90 °C
without laundry. Use standard
detergent.
ʑ
Status display
t
flashing.
Appliance has detected a
detergent overload.
– Too much detergent used?
Mix one tablespoonful of fabric softener with ½ litre water and pour
into compartment
II
(Not for outdoor fabrics, sportswear fabrics or
those made with down.)
–
Reduce the detergent dosage for the next wash cycle
.
ʑ
Loud noises, vibrations and
“wandering” during the
spin cycle.
– Are the appliance feet fixed?
Secure appliance feet
a
Installation instructions
.
– Transportation safety devices removed?
Remove transportation safety devices
a
Installation instructions
.
ʑ
Display panel/indicator
lamps do not function
during operation.
– Power cut?
– Circuit breakers tripped? Switch the circuit breakers back on or
replace.
– If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced-load detection system is adjusting the
imbalance by repeatedly redistributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
ʑ
There are detergent
residues on the laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Select
Rinse
m
or brush down the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to
Off
and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
a
Installation instructions.
siemens-home.com/welcome
Register
your
product
online
Washing machine
WM10B260IL
en
Washing machine
operating instructions
Observe the safety instructions on page 8.
Read these instructions and the separate installation
instructions before operating the washing machine.