Siemens UH50 FLOW SENSOR, Инструкции по настройке, Страница: 14 / 15

Ultraheat / Ultracold UH50 Configuration Instructions UH 106-101k Page 14 / 15
Display: MWh with 3 decimal places (as of qp 15 with
2 decimal places)
B
Display: MJ (until qp 3) C
Display: GJ with 3 decimal places (as of qp 3.5 with 2
decimal places)
D
Display: kWh (until qp 10), flashing G
Display: MWh with 3 decimal places (as of qp 15 with
2 decimal places), flashinh
H
Display: GJ with 3 decimal places (as of qp 6 with 2
decimal places), flashing
K
Display: m³ (for the flow meter) with 2 decimal places
(as of qp 40 with 1 decimal place)
V
Further features
Measurement dynamics Code
Dynamic range 1:100
C
other ranges on request
Modules as accessories
Power supply modules Code
Power supply 110V AC with 10m cable WZU-AC110-100
Power supply 110V AC with 1.5m cable WZU-AC110-15
Power supply 110V AC with 5m cable WZU-AC110-50
Power supply 230V AC with 10m cable WZU-AC230-100
Power supply 230V AC with 1.5m cable WZU-AC230-15
Power supply 230V AC with 5m cable WZU-AC230-50
Power supply 24V AC/DC with plug WZU-ACDC24-00
Power pack 230 V AC for analog
module WZU-AM
WZR-NE
Communication modules Code
Analog module WZU-AM
CL-Module WZU-CL
M-Bus module acc. to DIN 1434-3 (G2-
generation 2 – recommended until
meter FW 5.14)
WZU-MB
M-bus module (G2) with 30s minimum
reading cycle
WZU-MB-30
M-bus module (G2) with guaranteed
data set
WZU-MB-GR
M-Bus module G4 acc. to EN 13757 and
DIN 1434-3 (G4 - Generation 4 - FW
5.15 and higher)
WZU-MB-G4
M-Bus module G4 acc. to EN 13757 and
DIN 1434-3 (G4 - Generation 4 - FW
5.15 and higher) with 2 pulse inputs
WZU-MI
Pulse module WZU-P2
Pulse module with OptoMOS WZU-P2L
GSM Module with 2 pulse inputs, with
battery; SMS support
WZU-GM
GPRS module with ext. antenna
(magnetic attachment) and UH50 power
pack 110..230V / cable 5m; with
interface for up to 8 M-Bus
meter to be read over GPRS; amongst
others Email support
WZU-GPRS
Radio module WZU-RM
Radio module with external antenna WZU-RM-EXT
For mounting of temperature
sensors
Code
Adapter for ball valves to install temp-
erature sensors DS length 38 mm
WZT-KA
Mounting accessories for tubes Code
Kit extension from 110 mm G ¾B to
130 mm G 3/4 B (with seals)
WZM-V130
Kit extension from 110 mm G ¾B to
190 mm G 1 B (in pairs with seals)
WZM-V190
Spacer for heat meter DN 100 - 360
mm PN 16, incl. sealing disks
WZM-F360.100-16
Spacer for heat meter DN 100 - 360
mm PN 25, incl. sealing disks
WZM-F360.100-25
Notes
•
All regulations on the use of meters must be
observed.
•
Cavitation in the system must be avoided.
•
Meters up to DN25 may only be installed with
directly immersed sensors according to German
calibration law!
•
Install the unit in such a way that no water can
enter the electronic unit during operation.
•
User seals may only be removed by authorized
persons for service purposes and must be
replaced afterwards.
•
The unit is supplied with Installation and Service
Instructions and with Operating Instructions.
•
No later than 30 seconds after installation, the
meter detects the plugged modules automatically
and is ready for communication or pulse output.
•
The type of modules plugged can be displayed in
the service loop depending on how the display is
parameterized.
•
For fast pulses, the parameters must be set
accordingly with the service software.
•
Up-to-date versions of all instructions can be
found in the Internet at www.siemens.com/sbt
Siemens AG
Building Technologies
Please contact our next sales office