background image

Pressure Independent Control 

Technical Instructions 

SSD Series Electronic Valve Actuators 

Document No. 155-773 

 

September 1, 2015 

Siemens Industry, Inc. 

Page 3

 

 

Accessories 

 

Figure 1.  Conduit Connector. 

ASY97

 Conduit connector (quantity one). 

For SSD61U and SSD81U only. 

 

        

 

Figure 2.  Terminal Plug and  

Block Cover. 

Terminal plug and terminal block cover 
(quantity: one each). For SSD61U and 
SSD81U only. 

 

ASY99

 SSD81U actuator  

floating control.

 

 

ASY100 

SSD61U actuator  

0 to 10 Vdc control.

 

 

ASY98

 Replacement screw and nut for use on the conduit connector or the terminal 

connector, quantity one each. For SSD61U and SSD81U only. 

Warning/Caution Notations 

 

 

WARNING: 

 

Personal injury/loss of life may occur if you 
do not perform a procedure as specified. 

 

CAUTION: 

 

Equipment damage may occur if you do not 
perform a procedure as specified. 

 

 

Operation 

 

CAUTION:

 

A valve must be connected to the actuator before applying power.  

If applying power to the actuator when a valve is not connected, the 
actuator will respond to a control signal and the shaft will extend until it 
reaches its maximum end stop. Thereafter, it will not respond to any 
signal. If this occurs:  

1.  Disconnect power.  

2.  Turn the manual position indicator (see Figure 7

)

 on the top of the 

actuator to the 0 position and verify the actuator shaft completely 
retracts. 

3.  Connect a valve to the actuator. 

4.  Reapply power. The actuator will return to normal operation. 

Содержание SSD81U









Отзывы: