manualshive.com logo in svg

Siemens SITRANS WW300, Руководство по эксплуатации

Поделиться
Скачать
Siemens SITRANS WW300 Скачать руководство пользователя страница 13

 

SITRANS WW300 
Operating Instructions, 05/2015, A5E33560691-AB 

11

 

 

Installing 

4 

 

 

 

 

Note 
When lifting the weighfeeder, connect to the lifting points at the top of the unit, and follow 

local governing code for lifting/hoisting. 

 

Perform a thorough and systematic inspection of containers immediately upon receipt of your 

Siemens weighfeeder. The containers are packed to separate each item and provide protection 

during shipping. 

 

 

Note 
Do not remove equipment from shipping crates or boxes until you check for possible 

shipping damage. Contact the carrier immediately if damage is noted. 

 

Your weighfeeder has been designed, assembled, and factory tested for your specific 

application. 

 

 

Note 

•

 

The frame of the weighfeeder needs to be grounded to ensure accurate signal processing 

to the integrator. 

•

 

Do NOT remove the tagged load cell shipping bolt(s) until the installation is complete to 

prevent load cell damage. 

•

 

Do NOT weld on or near the weighfeeder while the load cell is connected to the electronic 

integrator. Damage to the integrator may result if the load cell is not disconnected from 

the integrator. 

•

 

Follow a scheduled, preventative maintenance program to ensure optimum performance 

and long equipment life. 

 

Содержание SITRANS WW300











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды