Siemens SITRANS LVL200H Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 40

Siemens SITRANS LVL200H Скачать руководство пользователя страница 27

27

MAN-100048

SITRANS LVL200H - Operating Instructions

49231-EN-170719

Error

Reason

Rectification

Red control lamp lights up

Error on the vibrating element

Check if the vibrating element is

damaged or extremely corroded.

Interference on the electronics mod-

ule

Exchanging the electronics module

instrument defective

Exchange the instrument or send it

in for repair

Depending on the reason for the fault and the measures taken, the

steps described in chapter "

Set up

" may have to be carried out again.

7.3 Exchanging the electronics

If the electronics module is defective, it can be replaced by the user.
In Ex applications only an electronics module with respective Ex ap-

proval may be used.
You can find all the information you need to carry out an electronics

exchange in the handbook of the new electronics module.
In general, all electronics modules of the respective type series can

be interchanged. The type name is stated on the electronics module.
If you want to use an electronics module with a different signal output,

you have to carry out the complete setup. You can find the required

operating instructions manual on our homepage.

7.4 How to proceed if a repair is necessary

If it is necessary to repair the instrument, please con-

tact Siemens. You find the locations on our homepage

"www.siemens.com/processautomation".

Reaction after fault recti-

fication

«
...
25
26
27
28
29
...
»

Содержание SITRANS LVL200H









































Отзывы:

Нет отзывов