manualshive.com logo in svg

Siemens SITRANS LVL200H, Руководство по эксплуатации, Страница: 11 / 40

Поделиться
Скачать
Siemens SITRANS LVL200H Скачать руководство пользователя страница 11

11

MAN-100048

SITRANS LVL200H - Operating Instructions

49231-EN-170719

3.4  Storage and transport

Your instrument was protected by packaging during transport. Its 

capacity to handle normal loads during transport is assured by a test 

based on ISO 4180.
The packaging of standard instruments consists of environment-

friendly, recyclable carton material. The sensing element is additional-

ly protected with a cardboard cover. For special versions, PE foam or 

PE foil is also used. Please dispose of the packaging material through 

specialised recycling companies.

Transport must be carried out in due consideration of the notes on the 

transport packaging. Nonobservance of these instructions can cause 

damage to the device.

The delivery must be checked for completeness and possible transit 

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and 

stored according to the orientation and storage markings on the 

outside.
Unless otherwise indicated, the packages must be stored only under 

the following conditions:

• 

Not in the open

• 

Dry and dust free

• 

Not exposed to corrosive media

• 

Protected against solar radiation

• 

Avoiding mechanical shock and vibration

• 

Storage and transport temperature see chapter "

Supplement - 

Technical data - Ambient conditions

"

• 

Relative humidity 20 … 85 %

With an instrument weight of more than 18 kg (39.68 lbs) suitable and 

approved equipment must be used for lifting and carrying.

3.5 Accessories

The pluggable display module LVL200-LED is used for clearly visible 

indication of the switching status. It can be attached to the electronics 

of the sensor and removed at any time.
You can find additional information in the operating instructions 

manual "

LVL200-LED

".

Screwed flanges are available in different versions according to the 

following standards: DIN 2501, EN 1092-1, BS 10, ASME B 16.5, 

JIS B 2210-1984, GOST 12821-80.
You can find additional information in the supplementary instructions 

manual "

Flanges according to DIN-EN-ASME-JIS

".

Packaging

Transport

Transport inspection

Storage

Storage and transport 

temperature

Lifting and carrying

LVL200-LED

Flanges

Содержание SITRANS LVL200H









































Отзывы:

Нет отзывов