manualshive.com logo in svg

Siemens SITOP PSU100S, Руководство по эксплуатации

Поделиться
Скачать
Siemens SITOP PSU100S Скачать руководство пользователя страница 64

Applications 

 

9.4 Overload protection in the 24 V output circuit 

 

SITOP PSU100S 

64

 

Operating Instructions, 02.2013, C98130-A7589-A1-3-7629 

9.4

 

Overload protection in the 24 V output circuit 

If overload occurs, the electronic current limiting of the SITOP PSU100S power supply limits 

the output current to a maximum value (refer to chapter Technical data (Page 39)). The 

output cables are protected against a thermal overload if they are dimensioned 

corresponding to the maximum rms output current, or protected using additional components 

(for example, miniature circuit breaker, fuses). 
However, a load circuit that fails as a result of overload, for instance, should frequently be 

reliably and quickly identified and specifically switched off before the power supply goes into 

current-limiting mode (in current-limiting mode, the supply voltage would also be reduced for 

all of the remaining 24 V loads). 
The SITOP PSE200U selectivity module with 4 channels (versions with adjustable output 

current range for each channel from 0.5-3 A and 3-10 A) is available; this monitors the 24 V 

branches for overloading and short-circuiting (Figure 9-4 Electronic protection of 24 V loads 

using the SITOP PSE200U selectivity module (Page 64)). Brief current peaks, e.g. as a 

result of a high inrush current, are permitted, and branches with a longer overload are 

switched into a no-current condition. This is also ensured for cables in a high-ohmic 

condition and for short-circuits that slowly develop over time. 
When a channel fails, the fault is signaled using a group signal contact or as a single 

channel signal, and the branch of the module involved is displayed using an LED.  
For versions with single channel signaling, function blocks for evaluation purposes are 

available for SIMATIC S7-1200/300/400, for STEP 7 Classik and TIA Portal at no charge. 
You can find additional information at: 
SITOP PSE200U selectivity module manuals 

 

3RZHUVXSSO\

6HOHFWLYLW\

PRGXOH

3/&

+0,

$FWXDWRUV

6HQVRUV

'&9

 

Figure 9-4 

Electronic protection of 24 V loads using the SITOP PSE200U selectivity module 

Содержание SITOP PSU100S









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды