Siemens SIRIUS 3RW44 Скачать руководство пользователя страница 164

Страница: 164 / 292

PROFIBUS DP communication module

9.6 PROFIBUS DP commissioning using the GSD file in STEP 7 (example)

3RW44 soft starters

164

Manual, 03/2017, NEB535219502000/RS-AB/008

9.6

PROFIBUS DP commissioning using the GSD file in STEP 7

(example)

9.6.1

Introduction

The following example shows you how to commission the PROFIBUS DP communication

module.

●

Installation and activation of the PROFIBUS DP communication module (fieldbus

interface)

●

Configuration with STEP 7 using the GSD file

●

Integration into the user program

●

Switching on

Components needed

●

3RW44 soft starter

●

3RW49 00-0KC00 communication module

General requirements

●

You have configured an infeed module with integrated S7 station,

●

e. g. with CPU315-2 DP.

●

You are proficient in STEP 7.

●

The programming device is connected to the DP master.

Software requirements

Table 9- 1

Software requirements for commissioning

Configuration software used

Version

Explanations

STEP 7

From version V5.1+SP2

onwards

You have integrated the GSD file of

the soft starter into STEP 7.

Configuration software for the

other DP master used

You have integrated the GSD file of

the soft starter into the applicable

configuration tool.

Содержание SIRIUS 3RW44





































































































































































































































































































Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды

Siemens SIRIUS 3RW44, Руководство пользователя

Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды